Manual Vonroc MS806AA (page 8 of 56) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish)

778563

Zoom out

Zoom in

1/56

WWW.VONROC.COM

Attaching The workpiece supports (Fig. E)

1. Slide the extension arm (4) out of the frame (9)

until the desired length is reached.

2. Now insert a extension arm knob (6) into the

corresponding hole on the frame turn it clock-

wise to secure the extension arm (4) in place,

as shown on ﬁgure E.

3. Insert a workpiece support (2) into the collar

on the extension arm (4). The side with the end

stop (5) should be facing inwards towards the

centre of the stand.

4. Insert a workpiece support knob (3) into the ex-

tension arm (4) and turn it clockwise to tighten

the workpiece support (2) into place.

7. Repeat the same procedure with the opposite

extension arm.

Attaching the mitre saw mounting bars (Fig. F)

Only use a mitre saw that has four ﬁxing

holes (one in each corner of the base) on

this stand. If the mitre saw does not meet

this requirement, do not use it with this

stand as the mitre saw cannot be properly

secured. Failure to follow this direction may

result in damage to property and/or

personal injury.

1. Ensure the mounting bar levers (14) are in

opened position (facing upwards).

2. Lower the front part of the mounting bars (7)

and subsequently the rear part onto the frame,

as shown on ﬁgure F.

3. Now lock the mounting bar into place by push-

ing the mounting bar levers (14) downwards.

Attaching A Mitre Saw (Fig. G, H)

During operation and before starting a new

job, ensure that all screws and nuts are

tightened correctly and securely.

1. Adjust the mounting bars (7) to roughly the

width of the mitre saw base.

2. Place the mitre saw on the mounting bars (7)

and line up the holes in the mitre saw base with

the slots on the mounting bars (7).

3. Feed a bolt through the bottom of the mounting

bar (7) then through the base of the mitre saw.

4. Slide a washer and then a spring washer onto

the bolt and fasten it with a nut.

5. Repeat steps 3 and 4 for the other four holes on

the mitre saw base.

Attaching other types of machines that do not ﬁt

the standard mounting bars

Do not mount a table saw on this miter saw

stand. Aggressive feeding of sheet

materials into the table saw could cause

the stand to tip over.

To mount different machine types (that do not ﬁt

onto the mitre saw mounting bars), VONROC offers

MS807AA universal machine supports. To mount

these universal machine supports:

1. Connect the universal machine supports to the

mounting bars (7) and secure them with 4 hex-

agonal screws, 4 washers, 4 spring washers and

4 hexagonal nuts as supplied with the MS807AA

universal machine supports.

2. Place your tabletop machine onto the universal

machine supports.

3. Fasten the tabletop machine with 4 hexagonal

screws, 4 washers, 4 spring washers and 4 hex-

agonal nuts as supplied with the Mitre saw stand.

4. Tighten the screws after assembly.

5. Fasten the mounting bars (7) with the mounted

tabletop machine on the mitre saw stand, as

described in ‘Attaching A Mitre Saw’

Visit www.vonroc.com or contact Vonroc customer

service to acquire the MS807AA universal machine

supports.

4. OPERATION

Do not use the mitre saw stand until it is

completely assembled and you have read

and understood this entire manual and the

manual of the tool being used with this

mitre saw stand.

Do not use the mitre saw stand for

scaffolding or as a ladder. Make sure to

securely tighten all fasteners before use.

Maximum capacity is 150kg. Power tools

on the mitre saw stand should not exceed a

combined overall height of 150cm from the

ﬂoor.

Adjusting The Extension Arms (Fig. E, I)

1. Turn the extension arm knob (6) on the frame

counter-clockwise to loosen it.

2. Pull the extension arm (4) out to the desired

length. Note: The maximum extension length

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc MS806AA in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 8.74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vonroc MS806AA Manual

Product: