778563
7
Zoom out
Zoom in
Previous page
1/56
Next page
EN
7
WWW.VONROC.COM
The universal tool stand is also designed as a work-
piece support when working with mitre saws, scroll
saws, circular table saws, and other similar electric
power tools. The maximum workpiece length is
3m. Additional workpiece supports may have to be
used (e.g. a roller trestle) in order to prevent longer
workpieces tilting. Attention: Ensure that the work-
piece support is secure and not tilted!
TECHNICAL SPECIFICATIONS
Model No. MS806AA
Max. permissible load 150kg
Opened dimensions
L: 1185-2000mm
W: 632mm
H: 900-1000mm
Closed dimensions 1380x474x301mm
Weight 24.9 kg
DESCRIPTION
The numbers in the following text refer to the pic-
tures on pages 2-5.
1. Roller
2. Workpiece support
3. Workpiece support knob
4. Extension arm
5. End stop
6. Extension arm knob
7. Mitre saw mounting bar
8. Carrying handle
9. Frame
10. Pin slot
11. Locking lever
12. Leg
13. Foot
14. Mounting bar lever
15. Mitre saw mounting hardware (bolts, washers,
spring washers, nuts)
16. Wheels
17. Axle bracket
18. Bolts for handle
19. Retaining rings for wheels
20. Bolts for axle bracket
21. Washer for axle bracket and handle
22. Spring washer for axle bracket and handle
23. Nut for axle bracket and handle
24. Adjustable foot
25. Material support
26. Adjustable nut
3. ASSEMBLY
Study each figure and identify the
components required with reference to the
contents table above.
Attaching the wheels (Fig. A, B)
1. Lay the mitre saw stand on the floor with the
folded legs (12) facing upwards.
2. Mount the axle bracket (17) onto the frame (9)
using the bolts (20), washers (21), spring wash-
ers (22) and nuts (23) as shown on figure A.
3. Now slide the wheels (16) onto the axles of the
axle bracket (17) as shown on figure B. Note:
raised hub goes on the inside.
4. Secure the wheels (16) by attaching the retain-
ing rings (19) onto the axle ends of the axle
bracket (17).
Attaching the handle (Fig. C)
Mount the handle (8) onto the frame (9) using the
bolts (18), washers (21), spring washers (22) and
nuts (23) as shown on figure C.
Unfolding The Stand (fig. D)
1. Lay the mitre saw stand on the floor with the
folded legs (12) facing upwards.
2. Depress the locking lever (11) and unfold the
two upper legs (12) until the spring-loaded pin
(11) clicks into the pin slot (10).
3. Repeat the same procedure for the other two
legs.
4. Lift the stand and flip it into the upright position.
5. Check that the stand is stable and all of the leg
locking pins have engaged properly.
Folding The Stand
One pair of legs on the stand must fold firstly for
the stand to fold flat. The legs have not folded into
place if the locking levers (11) do not pop into place.
The legs should not swing about when the stand is
picked up if the legs have locked into position.
1. Turn the mitre saw stand upside down on the
floor with the legs (12) sticking up.
2. Depress the spring-loaded pin (11) on the lower
pair of legs and fold them in.
3. Repeat the same procedure on the other pair of
legs.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc MS806AA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc MS806AA in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 8.74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info