764069

Vonroc LD503DC Manual

8
Zoom out
Zoom in
Previous page
1/44
Next page
8
EN
WWW.VONROC.COM
4. Aiming the laser onto the target and quickly
pressing the measure button (2) again for
measuring the width.
5. Pressing the measure button (2) will activate
the laser.
6. Aiming the laser onto the target and quickly
pressing the measure button (2) again for
measuring the second width. The calculated re-
sult is shown in the main line and the measured
value above.
Single pythagorean measurement (Fig. A+I)
Press the function button (3) to change measure-
ment function to single pythagorean measurement.
Select the function and begin the measurement.
1. Pressing the measure button (2) will activate
the laser.
2. Aiming the laser onto the target and quickly
pressing the measure button (2) again for
measuring the upper point. The result is dis-
played immediately.
3. Pressing the measure button (2) will activate
the laser.
4. Aiming the laser rectangular onto the target and
quickly pressing the measure button (2) again
for measuring the lower point. The calculated
result is shown in the main line and the measu-
red value above.
Addition(+) and subtraction (-) function (Fig. A+J)
1. When the device is switched on, quickly press
the measure button (2) to activate the laser
(10).
2. Aiming the laser onto the target and quickly
press the measure button (2) again will trigger
single-mode measurement; the result is dis-
played immediately.
3. Quickly press the addition (5) or subtraction (6)
button.
4. Quickly press the measure button (2) to activate
the laser (10).
5. Aiming the laser onto the target and quickly
press the measure button (2) again will trigger
single-mode measurement. The calculated re-
sult is shown in the main line and the measured
value above.
This process can be repeated as required. The
same process can be used for adding (+) or
subtracting (-) areas or volumes.
Display Notices
The following errors can be corrected.
Message
Code Cause Remedy
Err08 Background brightness
too high Use dark colored target
Err10 Battery too low Change batteries
Err15 Out of range Measure target within the
range
Err16 Received signal too weak
Use light colored target;
Hold Quick Measure more
steadily
5. MAINTENANCE
Cleaning
NOTICE! Risk of product damage! Never
submerge device in water while cleaning.
Do not use cleaning agents or solvents.
Wipe the device using a dry cloth.
Storage
NOTICE! Risk of product damage! Always
handle measuring instruments with care.
• Store the product in a dry, well-ventilated place.
• Only store and transport the product in its origi-
nal packaging.
• Prevent large temperature fluctuations: Always
temper the product for a while before use in
extremely cold or hot environments.
Taking out of operation for a longer period of time
• When not in use for a longer period of time,
remove the batteries.
NOTICE! Risk of product damage!
Old, leaky batteries can damage the
product. Check the battery regularly.
ENVIRONMENT
Faulty and/or discarded electrical or
electronic apparatus have to be collected at
the appropriate recycling locations.
Only for EC countries
Do not dispose of power tools into domestic waste.
According to the European Guideline 2012/19/EC
for Waste Electrical and Electronic Equipment and its
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc LD503DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc LD503DC in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 5,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info