764069

Vonroc LD503DC Manual

7
Zoom out
Zoom in
Previous page
1/44
Next page
EN
7
WWW.VONROC.COM
Clear button (Fig. A)
Press clear button (8) to clear the last command or
displayed data.
Unit conversion (Fig. A)
The instrument’s default unit is meters but can be
set to meters ‘m’, feet ‘ft’ and inches ‘in’. Press the
units button (7) to switch between units of measu-
rements.
Adjusting measuring reference (Fig. A+C)
When the device is switched on, quickly press the
measuring reference button (4) to adjust the measu-
re reference. It’s possible to measure from the front
or the rear of the device.
Distance is measured from the rear of the
device (standard setting).
Distance is measured from the front of the
device.
Memory (Fig. A)
When the device is switched on, quickly press the
addition (5) or subtraction (6) button. Last 20 values
are displayed. Quickly press the addition (5) or
subtraction (6) button to navigate through last 20
values.
Measuring
WARNING! Risk of injury due to laser beam!
Never direct the measuring beam towards
people, other living creatures or reflecting
surfaces.
Target surfaces: Measuring errors can occur
when measuring to colorless liquids, glass,
styrofoam or semi-permeable surfaces or
when aiming at high gloss surfaces. Against
dark surfaces the measuring time increases.
Single-mode measurement (Fig. A+D)
When the device is switched on, quickly press the
measure button (2) to activate the laser (10). Aiming
the laser onto the target and quickly press the
measure button (2) again will trigger single-mode
measurement; the result is displayed immediately.
Continuous-mode measurement (Fig. A+E)
When the device is switched on, holding down the
measure button (2) will trigger continuous-mode
measurement. The current measurement is shown
in the main line and the Minimum(E2) and maximum
(E3) measured values above.
Area measurement (Fig. A+F)
Press the function button (3) to change measu-
rement function to area measurement. Select the
function and begin the measurement.
1. Pressing the measure button (2) will activate the
laser.
2. Aiming the laser onto the target and quickly pres-
sing the measure button (2) again for measuring
the length. The result is displayed immediately.
3. Pressing the measure button (2) will activate the
laser.
4. Aiming the laser onto the target and quickly pres-
sing the measure button (2) again for measuring
the width. The calculated result is shown in the
main line and the measured value above.
Volume measurement (Fig. A+G)
Press the function button (3) to change measure-
ment function to volume measurement. Select the
function and begin the measurement.
1. Pressing the measure button (2) will activate the
laser.
2. Aiming the laser onto the target and quickly pres-
sing the measure button (2) again for measuring
the length. The result is displayed immediately.
3. Pressing the measure button (2) will activate the
laser.
4. Aiming the laser onto the target and quick-
ly pressing the measure button (2) again for
measuring the width. The result is displayed
immediately.
5. Pressing the measure button (2) will activate the
laser.
6. Aiming the laser onto the target and quickly pres-
sing the measure button (2) again for measuring
the height. The calculated result is shown in the
main line and the measured value above.
Double area measurement (Fig. A+H)
Press the function button (3) to change measure-
ment function to double area measurement. Select
the function and begin the measurement.
1. Pressing the measure button (2) will activate the
laser.
2. Aiming the laser onto the target and quickly pres-
sing the measure button (2) again for measuring
the height. The result is displayed immediately.
3. Pressing the measure button (2) will activate the
laser.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc LD503DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc LD503DC in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 5,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info