764069

Vonroc LD503DC Manual

6
Zoom out
Zoom in
Previous page
1/44
Next page
6
EN
WWW.VONROC.COM
TECHNICAL SPECIFICATIONS
Model No.
LD502DC LD503DC
Measurement range *
0.05m-40m 0.05m-60m
Measuring Accuracy ** ± 1.5mm
Laser type 620 ~ 690 nm
Laser class II (<mW) acc.
To EN60825-1: 2014;
Single-mode measurement m, ft, in
Continuous-mode
measurement m, ft, in
Area measurement
m, ft, in
(automatic calculation)
Area measurement (double)
m, ft, in
(automatic calculation)
Volume measurement
m, ft, in
(automatic calculation)
Single pythagorean
measurement
Yes
Addition and subtraction
function Yes
Bubble level Yes
Laser point Yes
Memory capacity (values) 20
Operating temperature 0~40 °C
Storage temperature 5~30 °C
Laser auto switch off Yes, after 15s
Instrument auto switch off Yes, after 30s
Battery 2x 1.5V type LR03 AAA
(alkaline)
Weight (Without Batteries) 108 g
Dimensions 119 x 52 x 26 mm
* Maximum deviation error or shorter range can
occur when laser exposed to bright sunlight, opera-
ted across very rough or minimal reflective surface,
or used during extreme temperature conditions.
** When measuring within 10 m, measurement ac-
curacy is ± 1.5 mm; more than 10 m, measurement
accuracy is calculated as follows: ±1,5 mm± 0.05*
(D-10) (D: Measuring Distance, Unit: m).
DESCRIPTION
The numbers in the text refer to the diagrams on
page 2-4.
Fig. A
1. Display
2. Switch on / measure button
3. Function
4. Measurement reference (measurement from
the back or the front of the device)
5. Addition
6. Subtraction
7. Selection of the measurement unit
8. Clear / switch off button
9. Bubble level
10. Laser beam outlet
11. Reception lens
Fig. B
12. Battery cover
3. ASSEMBLY
Inserting / Replacing the Batteries (Fig. B)
1. Remove the battery compartment cover (12).
2. lnsert batteries with correct polarity according
to indications.
3. Close the battery compartment cover (12).
4. OPERATION
WARNING! Danger of injury due to defective
components! The product must only be put
into operation if no defects are found. Ensu-
re that any defective parts are replaced
before the product is used again.
Check the device:
• Make sure all parts are fitted on the machine
firmly.
• Check whether there are any visible defects:
broken parts, cracks, etc.
Switch on and off (Fig. A)
Press the measure button (2) to switch on the
device. Device will always start in the default
reference setting of single measurement mode.
Hold down the switch off button (8) to switch off
the equipment.
Automatically switch off
The laser will be switched off automatically after 15
seconds and the device will be powered off after
30 seconds of inactivity.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vonroc LD503DC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vonroc LD503DC in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 5,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info