769323
49
Zoom out
Zoom in
Previous page
1/96
Next page
D-307500 PowerMaster 360 Installer's Guide 49
4.9 Diagnostics
4.9.1 General guidance Diagnostic flow-chart & menu options
The DIAGNOSTICS menu enables you to test your system and to verify proper operation of your PowerMaster-360
panel, wireless devices attached to it, and the communication (GSM/GPRS/SIM) modules.
IMPORTANT! Reliable reception must be assured during the initial testing and also throughout subsequent system
maintenance. A device should not be installed in location where signal strength is poor. If you get poor signal
strength from a certain device, re-locate it, and re-test until good or strong signal strength is received. This principle
should be followed throughout the diagnostic test procedure.
The diagnostic test process is shown below.
The 07.DIAGNOSTICS menu contains several sub-menu options, each covering a group of configurable features and
parameters related to the communication and reporting as follows (see the list in Step 3 of the chart below):
Option
Description of Option Features and Parameters
Section
WL DEVICES
Describes how to test the devices attached to the PowerMaster-360 panel, review
devices' status and RF signal status. You can test all devices, test single device,
review devices status and review RF problems, in case of any.
4.8.2
GSM/GPRS
Describes how to test the GSM/GPRS communication module.
4.8.3
SIM NUMBER TEST
Tests the SIM number to ensure correct entry of the SIM number in the control
panel.
4.8.4
BROADBAND
MODULE 1
Enables to test the communication of the Broadband Module with the
PowerManage server.
4.8.5
WLAN
Tests the communication of the WLAN module with the PowerManage server.
4.8.6
To enter the 07.DIAGNOSTICS menu and to select and configure an option, proceed as follows:
Step 1
Step 2
Step 3
Step 4
Select "07.DIAGNOSTICS"
Select sub-menu option
Select the diagnostics you want to perform
See
INSTALLER MODE
07.DIAGNOSTICS
WL DEVICES
TEST ALL DEVICES
4.8.2
SHOW ALL DEVICES
SHOW RF PROBLEMS
TEST ONE DEVICE
Contact sensors
Motion sensors
Repeaters
GSM/GPRS
4.8.3
SIM NUMBER TEST1
Tst by IP RCVR 1
Tst by IP RCVR 2
SIM# verified
4.8.4
BROADBAND MODULE2
PLEASE WAIT…
Unit is OK
4.8.5
WLAN
PLEASE WAIT…
Unit is OK
4.8.6
4.9.2 Testing wireless devices
The PowerMaster-360 enables to test the wireless devices attached to the panel. You can test all devices, one device
at a time, display devices' status, and review any RF problems.
07:DIAGNOSTICS  WL DEVICES  MENU required
1
The name of the product is PowerLink3 IP Communicator
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Visonic Powermaster-360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Visonic Powermaster-360 in the language / languages: English as an attachment in your email.

The manual is 2.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info