769323

Visonic Powermaster-360 Manual

50
Zoom out
Zoom in
Previous page
1/96
Next page
50 D-307500 PowerMaster 360 Installer's Guide
Enter the WL DEVICES menu, select the type of test you require to perform (see guidance above and in section 4.8.1),
then refer to the table below which provides you with detailed explanations for each option.
Option
Instructions
TEST ALL DEVICES
You can test all wall-mounted devices automatically, one after the other, after which the
installer tests the other devices in the following order: vanishing magnetic contact
devices, keyfobs and then panic buttons.
While in TEST ALL DEVICES, press to initiate the test. The following screen will
appear: TESTING Xxx NNN, where Xxx indicates the type of device and NNN indicates the
number of enrolled devices in the panel that have not been tested yet. This number automatically
drops one count for every tested device.
Pressing any key during the testing process will open the following options:
1. Press to jump to the next device group. For example, from wall-mounted devices to
keyfobs.
2. Press to continue the testing process
3. Press to exit the test process.
When all wall-mounted devices have completed the test procedure, you can test vanishing
magnetic contact devices.
While in the vanishing test process, indicated by the corresponding display, for example,
TEST VANISH NNN, momentarily open the door or window.
When all vanishing magnetic contact devices have been tested, you can test keyfobs.
While in the keyfobs test process, indicated by the corresponding display, for example,
TEST KEYFOBS NN, press any key of the selected device to initiate the test.
When all keyfobs have been tested, you can test panic buttons.
While in the panic button test process, indicated by the corresponding display, for example,
TEST PANIC BT. NN, press a button on the pendant.
At the end of the test process, the panel will present the following: SHOW ALL DEVICES.
Press to view devices' status.
Note: Refer to SHOW ALL DEVICES section below for further information on device status.
TEST ONE DEVICE
CONTACT SENSORS
MOTION SENSORS
GLASSBREAK SENS.
SHOCK SENSORS
SMOKE SENSORS
CO SENSORS
GAS SENSORS
FLOOD SENSORS
TEMPERATURE SENS.
KEYFOBS
PANIC BUTTONS
KEYPADS
SIRENS
REPEATERS
You can select a specific device group you require to test, for example, Motion Sensors.
Press to enter the TEST ONE DEVICE sub menu and use to scroll through the
device families. Press to enter the <device family> sub menu, for example:
MOTION SENSORS.
Note: If there is no enrolled device,
NO EXISTING DEV.
will be displayed.
The following screens will then appear: Xxx:<device name> <location>, where Xxx
indicates the device number. You can now select a specific device.
Press to test the selected device. The following screen will appear: TESTING Xxx 001.
While in the keyfobs, panic button or vanishing magnetic contact test process, indicated
by the corresponding display, for example, Xxx ACTIVATE NOW, press any key of the
selected keyfob or panic buttons, or momentarily open the door or window, to initiate the
test.
At the end of the test process, the panel will present the devices' status:
Xxx: 24hr: <status>1 Xxx: NOW: <status>1.
Note: Refer to the SHOW ALL DEVICES section for further information on device status.
SHOW ALL DEVICES
You can view the devices status.
Note: This option is available only after testing process was done.
Press to view the devices' status.
The following screens will appear: Xxx: 24hr: <status>1 Xxx: NOW: <status>1
Use to scroll between the device's families.
1
The signal strength indications are as follows: STRONG; GOOD; POOR; 1-WAY (the device operates in 1-way mode
or, the NOW communication test failed); NOT TST (results are shown without any performed test); NOT NET [device
is not networked (not fully enrolled)]; NONE (keyfob 24Hr result); or EARLY (result of the last 24Hrs without
… 50 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Visonic Powermaster-360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Visonic Powermaster-360 in the language / languages: English as an attachment in your email.

The manual is 2.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info