769323

Visonic Powermaster-360 Manual

21
Zoom out
Zoom in
Previous page
1/96
Next page
D-307500 PowerMaster 360 Installer's Guide 21
The panel is set to the Enrollment mode (step #2 above) and the device is enrolled using the Enroll button (refer to the
device information in the device Installation Instructions, then open the device and identify the Enroll button). For
keyfobs and keypads, use the AUX '' button. For gas detectors, insert the battery.
Press the enroll button for 2-5 seconds until the LED lights steadily and then release the button. The LED will
extinguish or may blink for a few more seconds until the enrollment is completed. If enrollment is successfully
completed, the PowerMaster-360 sounds the Success Tune and the Virtual Keypad momentarily shows DEVICE
ENROLLED and then reads the device details.
Enrolling a Wired Input
To enroll a wired input to the detector, the following process should be followed:
- Adding a Wired Input
[1]
[2]
[3]
[4]
Enter INSTALLER MODE, and select 02:ZONES DEVICES (see section 4.2) .
Select ADD WIRED SENSOR.
Select the required sensor group, for example Contact Sensors, Shock Sensors.
Select the required device.
[5]
Select the required PIN number from the HW INPUT PIN #.
The input is enrolled as a zone, for example:Z02: Wired Sensor with ID number 053-XXXX.
[6]
Scroll to select the required zone number, location, zone type, chime configuration, and device setting.
The device settings for a wired input include the following Wiring Type options:
- EOL– end of line
- Normally open
- Normally closed
- Double EOL (not available for all devices – see device installation instructions)
[NOTE:]
Once a wired input is enrolled to a device, the menus Input #1 (for MC-302 E) and Aux Input (for SD-304)
are not available for further configuration in the device’s Device Settings.
[NOTE:]
Deleting the device will automatically delete its wired input.
Enrolling a PGM Output
To enroll a PGM output to the detector, the following process should be followed:
- Adding a PGM Input
[1]
[2]
[3]
[4]
Enter INSTALLER MODE, and select 02:ZONES DEVICES (see section 4.2) .
Select ADD PGM OUTPUT.
Select the required sensor group (Contact Sensors).
Select the required device.
[5]
Select the required PIN number from the PGM OUTPUT PIN #.
[6]
Scroll to select the required location name.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Visonic Powermaster-360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Visonic Powermaster-360 in the language / languages: English as an attachment in your email.

The manual is 2.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info