769323
20
Zoom out
Zoom in
Previous page
1/96
Next page
20 D-307500 PowerMaster 360 Installer's Guide
ADD TO SOAK TEST
To enable the Soak Test for device zones.
4.4.6
DEFINE DEFAULTS
To customize the defaults of the device's parameters according to your personal
preferences for each new device enrolled in the system.
4.4.7
4.4.2 Adding new wireless devices
Part A - Enrollment
To enroll and configure a device, follow the instructions in the following chart:
Step 1
Step 2
Step 3
Step 4
Select ADD NEW
DEVICE Option
[1]
Enroll the device or
Enter the device ID
[2]
Select a Zone number
[3]
Configure zone &
device Parameters
[4]
ADD NEW DEVICE
ENROLL NOW or
ENTR ID:XXX-XXXX
Z01:Motion Sens
ID No. 120-1254
Continue to the 2nd
diagram in Part B below
Press the enrollment
button or enter the device
ID. Refer to the detailed
instructions below
Z10:Motion Sens
ID No. 120-1254
- Adding New Devices
[1]
Enter INSTALLER MODE, select 02:ZONES DEVICES (see section 4.2) and then select ADD NEW DEVICE.
Because of encryption, PowerG devices (including Keyfobs) cannot be used on more than one system at one
time. Remember to verify panel and device compatibility.
[2]
See enrollment by button or device ID below. If enrollment is successful, the display reads DEVICE ENROLLED
(or ID ACCEPTED) and then shows the device details - see [3]. However, if the enrollment fails, the display will
advise you the reason for failure, for example: ALREADY ENROLLED or NO FREE LOCATION.
If the enrolled device is adapted to operate as another device that the panel recognizes, the display then reads
ADAPTED TO <OK>.
[3]
The display shows the device details and the first available free Zone number for example: Z01:Motion Sensor >
ID No. 120-1254 (or K01:Keyfob / S01:Siren etc. depending on the type of the enrolled device).
Detectors can be enrolled in any zone number. To change the zone number, click the button or type in
the zone number, and then press to confirm.
[4]
Continue to Part B to configure the device – see diagram below
Checking panel to device compatibility
Each PowerG device bears a 7-character Customer ID printed on the device sticker in the format: FFF-M:DDD, (for
example, 868-0:012) where FFF is the frequency band and M:DDD is the variant code.
For PowerG system devices compatibility, make sure the frequency band (FFF) and the variant code (M) of the devices
match. The DDD can be ignored if the panel displays ANY for DDD.
Enrollment by using Device ID
The 7-digit Device ID can be used to register a device into the panel locally or from a remote location using the Remote
Programmer PC software. The enrollment by device ID is a 2 stage procedure.
In the 1st stage you register the devices' ID numbers into the panel and complete the device configuration. This can be
done from a remote location using the Remote Programmer PC software. Following the 1st stage, the PowerMaster-360
panel waits for the device to appear on the network in order to complete the enrollment.
In the 2nd stage, the enrollment is completed when the panel is in full working mode by inserting the battery into the
device, or by pressing the tamper or enrollment button on the device. This procedure is very useful for adding devices
to existing systems without the need to provide technicians with the Installer Code, or to allow access to the
programming menus.
Notes:
1. The system will display NOT NETWORKD until the 2nd stage of all registered devices is completed.
2. The Soak Test on pre-enrolled zones can be activated only when the zone is fully enrolled.
Enrollment using the Enrollment button
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Visonic Powermaster-360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Visonic Powermaster-360 in the language / languages: English as an attachment in your email.

The manual is 2.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info