769323
19
Zoom out
Zoom in
Previous page
1/96
Next page
D-307500 PowerMaster 360 Installer's Guide 19
To change your Master Installer or Installer Codes proceed as follows:
Step 1
Step 2
Step 3
Step 4
Select 01:INSTALL
CODES Option
[1]
Select Master Installer,
Installer code or Guard
code
[2]
Enter NEW Master Installer,
Installer code or Guard code
[3]
INSTALLER MODE
NEW MASTER CODE
MASTER CODE 999
to step 2
to step 2
ENTER CODE:
or
or
NEW INST. CODE
INST. CODE 888
or
or
01:INSTALL CODES
NEW GUARD CODE
GUARD CODE 000
to step 2
Setting Installer Codes
[1]
Enter the Installer Mode menu and select the 01:INSTALL CODES option (see section 4.2).
[2]
Select the NEW MASTER CODE, NEW INST. CODE or NEW GUARD CODE. Some panels may have only the
Installer Code and New Guard Code option.
[3]
Enter the new 4-digit Code at the position of the blinking cursor and then press .
Notes:
1. Code 0000 is not valid for Master Installer or installer.
2. Inserting 0000 for the Installer will delete the Installer Code.
3. Warning! Always use different codes for the Master Installer, for the Installer and for the Users.
If the Master Installer Code is identical to the Installer code, the panel will not be able to recognize the
Master Installer. In such a case, you must change the Installer code to a different code. This will re-validate
the Master Installer code.
4.3.1 Identical installer and master installer codes
In a 2-installer code system, the non-master installer may inadvertently change his Installer Code to that of the Master
Installer Code. In this case, the panel will allow the change in order to prevent the non-master installer from realizing
the discovery of the Master Installer's Code. The next time the Master Installer enters the Installer Mode the Master
Installer will be considered as an Installer and not as a Master Installer. In such a case the Master Installer should use
one of the following two solutions:
1. Access the panel using the Remote Programmer PC software application and change the Master Installer
Code to a different code than the one programmed by the Installer.
2.
a) Change the Installer Code to a temporary code
b) Exit the Installer Mode
c) Enter the Installer Mode again using the Master Installer code (the Master Installer Code will now be
accepted).
d) Change the Master Installer code to a different code.
e) Change the NON-Master Installer Code back again (that is, undo the change to the temporary code) so
that the NON-Master Installer can still enter the system.
4.4 Zones and devices
4.4.1 General guidance & ZONES/DEVICES menu options
From the ZONES/DEVICES menu you can add, configure, and delete devices.
To select an option follow the instructions below. See section 4.2 for more information.
INSTALLER MODE
02:ZONES/DEVICES
MENU required
indicates scroll
and select
Option
Use
Section
ADD NEW DEVICES
To enroll and configure the device's operation according to your preference and
in the case of sensors to also define their zone name (location), zone type, and
chime operation.
4.4.2
DELETE DEVICES
To delete devices from the system and to reset their configuration.
4.4.3
MODIFY DEVICES
To review and/or change the device's configuration.
4.4.4
REPLACE DEVICES
To replace faulty devices with automatic configuration of the new device.
4.4.5
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Visonic Powermaster-360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Visonic Powermaster-360 in the language / languages: English as an attachment in your email.

The manual is 2.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info