667332

Viking MT 5097 Manual

37
Zoom out
Zoom in
Previous page
1/290
Next page
ENES
35
PTEL
0478 192 9807 C - EN
● Drive the ride-on mower onto the lawn.
Do not engage the mowing deck in tall
grass or when set to the lowest cutting
level. Only engage the mowing deck
when the machine is already on the
area to be worked.
● Forwards mowing:
Select the forward driving direction
(Ö 8.9), then engage the mowing deck
by pressing the mowing deck switch or
mowing deck button. (Ö 8.5), (Ö 8.6)
Reverse mowing:
Select the reverse driving direction
(Ö 8.9) and briefly press the reverse
mowing safety switch (Ö 8.8) once,
then engage the mowing deck by
pressing the mowing deck switch or
mowing deck button within 6 seconds.
(Ö 8.5), (Ö 8.6)
During mowing:
● Set the throttle lever to the MAX
position. (Ö 8.2), (Ö 8.3)
● Always adapt the driving speed to the
grass height/cutting level.
A low driving speed should be selected
when mowing tall grass/at a low cutting
level.
Changing the driving direction with the
mowing deck engaged:
● For reverse mowing, briefly press the
reverse mowing safety switch once
within the designated time window
(5 seconds/1 second after switching).
(Ö 8.8)
● Bring the machine to a standstill on the
lawn and set the required driving
direction using the driving direction
selector lever. (Ö 8.9)
● Continue mowing.
Disengage the mowing deck in the
following sequence:
● Drive onto an area of grass which has
already been mown or select the
highest cutting level. (Ö 8.15)
● Disengage the mowing deck by
pressing the mowing deck switch or
mowing deck button. (Ö 8.5), (Ö 8.6)
13.8 Programming automatic
disengagement of the mowing deck
The electromagnetic blade clutch
can be programmed so that the
mowing deck is automatically
disengaged when the grass catcher box is
full. This enhances operating convenience
as blockage of the discharge chute is
prevented.
● Stop the engine. (Ö 13.3)
● Turn the ignition key to the "ignition on"
position. (Ö 8.1)
● Wait for the electronics self-diagnosis –
do not press any buttons.
Activating automatic disengagement:
● Press the reverse mowing safety switch
and actuate the drive pedal at the same
time for 5 seconds.
A short beep signals that automatic
operation is switched on.
● The current setting is permanently
saved.
Deactivating automatic
disengagement:
● Press the reverse mowing safety switch
and actuate the drive pedal at the same
time for 5 seconds.
Three beeps in quick succession signal
that automatic operation is switched off.
● The current setting is permanently
saved.
Programming automatic
disengagement using the Mode button
(only with MT 6112 C, MT 6112 ZL,
MT 6127 ZL):
● Keep the mowing deck button pressed
and press the Mode button at the same
time – automatic disengagement is
switched on or off using the Mode
button (ON or OFF appears on the
display).
● The current setting is permanently
saved.
Checking the programming (only with
MT 6112 C, MT 6112 ZL, MT 6127 ZL):
● Press and hold the mowing deck
button. The mowing deck active symbol
and the text ON or OFF appear on the
display.
ON – The mowing deck is automatically
disengaged when the grass catcher box
is full.
OFF – The mowing deck is not
automatically disengaged when the
grass catcher box is full.
A permanent continuous tone
signals that the grass catcher box is
full. (Ö 13.9)
Risk of injury!
After disengaging the mowing deck,
beware of the mowing blade
running on for up to 7 seconds
before coming to a standstill.
(Ö 12.)
… 37 …


Need help? Post your question in this forum.

Forumrules
1

Forum

viking-mt-5097

Reset search

  • how do i replace the transmission cable on the Viking MT 5097.oz Serial number 980075680
    Submitted on 4-10-2024 at 18:46

    Reply Report abuse

  • I need to change the ground drive belt in my MT 5097. Are there any instructions available for this? Submitted on 4-4-2022 at 18:58

    Reply Report abuse

  • I need to replace the drive belt in my MT 5097. Are there any instructions available for this? Submitted on 4-4-2022 at 18:57

    Reply Report abuse

  • Hello,
    We Have a Viking MT 5097Z.
    The engine stopped at once.
    When i turn on the Key to run it, the 10A fuse melts (twice) - not the 15A fuse.
    Is it possible one relay is broken (short-circuit) ? - N° 18,19, 25, 26 on the electric map -
    Or what other possibility?
    Thank's for your answer
    Best regards
    Franck
    Submitted on 4-1-2022 at 12:40

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viking MT 5097 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viking MT 5097 in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 24,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Viking MT 5097

Viking MT 5097 User Manual - German, Dutch, French, Italian - 284 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info