667212
38
Zoom out
Zoom in
Previous page
1/454
Next page
0478 121 9917 E - EN
36
9.2 Mowing on slopes
For safety reasons, the lawn mower
must not be used on inclines of
more than 25°. A slope inclination of
25° (46.6%) corresponds to a vertical
height increase of 46.6 cm for a 100 cm
horizontal distance.
9.3 Correct motor load
Do not switch on the lawn mower in tall
grass or at the lowest cutting height.
The lawn mower load must never cause
the motor speed to drop significantly.
If the speed drops, select a higher cutting
height setting and/or reduce the rate of
feed.
9.4 If the mowing blade blocks
Switch off the motor immediately and
disconnect the plug. Then eliminate the
cause of the fault.
9.5 Thermal motor overload protection
If an overload of the motor occurs during
operation, the built-in thermal overload
protection device automatically
deactivates the motor.
Causes for an overload:
mowing excessively high grass or
cutting height adjusted too low,
excessive rate of feed,
inadequate cleaning of the cooling air
guide (inlet slots),
mowing blade is blunt or worn,
unsuitable or excessively long electric
cable – voltage loss (Ö 11.1).
Recommencing operation
Resume normal operation of the machine
following a cooling period of up to 10 min
(depending on the ambient temperature)
(Ö 11.).
10.1 Two-hand operation
The motor can only be switched on by
pressing and holding the start button with
the right hand and then pulling the
motorstop lever to the handlebar with the
left hand.
10.2 Motor run-down brake
When the motorstop lever is released, the
mowing blade comes to a complete
standstill in less than three seconds.
An integrated motor run-down brake
shortens the run-down time until the blade
stops.
11.1 Electrical connection
Only electric cables which are no lighter
than rubber sheathed cables H07 RN-
FDIN/VDE0282 may be used as electric
cables.
Recommended minimum cross-
section:
up to 25 m Length: 3 x 1.5 mm²
up to 50 m Length: 3 x 2.5 mm²
The connectors of the electric cable must
be made of rubber or have a rubber cover
and conform to the standard
DIN/VDE 0620.
The mains voltage and mains frequency
must correspond to the information on the
identification plate and the information
contained in the section
"Technical specifications" (Ö 18.).
The power cable must be adequately
protected by a fuse (Ö 18.).
This machine is intended for operation with
a power supply having a system
impedance of Z
max
at the transfer point
(house connection) of maximum
0.49 ohms (at 50 Hz).
11
10. Safety devices
11. Operating the machine
Danger of electric shock!
Observe the safety instructions in
the section "For your safety" (Ö 4.).
If using a cable drum, the
connection cord must be unwound
completely, otherwise electrical
resistance may cause loss of power
and overheating.
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viking ME 339C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viking ME 339C in the language / languages: All languages as an attachment in your email.

The manual is 25,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info