661546
66
Zoom out
Zoom in
Previous page
1/80
Next page
Battery charger / inverter COMBI-GAMMA
66 090138.02
Use these settings to switch off the Aux-Relay 1 when battery voltage becomes higher •
than a certain limit (E2-05) for a certain time (E2-06)
Note: If E2-06=0 sec (Initial setting), then E2-05 is ignored.*
E2-07: Charging for ? sec
This setting switches the Aux-Relay 1 OFF when the • AC CHARGER started for a certain time
(E2-07). This can be useful when the Aux-Relay 1 is for instance used a low battery alarm.
Use the • Set Udc Lower than ? Voltage (E1-03) setting to start the alarm and use this set-
ting (E2-07) to stop it.
Note: As along as the battery voltage is lower than the specified limit (E1-03), the alarm *
will be active.
E2-08: Fan OFF for ? sec
This will switch the Aux-Relay 1 OFF when the internal fan switches off. This can be used •
together with the E1-08: Fan ON for ? sec setting to drive an external fan.
E2-09: Charge finished for ? Min (When E2-09=0, ignore this setting)
This condition becomes active when the charge bulk phase is finished for a certain time •
(E2-09).
For the charge curve, take a look at for instance the • Charge Current (D1-08) setting.
This is useful when the Aux-Relay 1 is used to start a generator. Once started, one might •
want to keep the generator on until the batteries are more or less charged.
E2-10: Aux-Relay 1 not ON for ? minutes (When E2-10=0, ignore this setting)
If one does not need special off condition, one can use this setting and the Aux-Relay •
1 will switch off automatically when there has been no ON condition for a certain time
(E2-10).
E2-11: AC IN loss for ? sec (When E2-11=0, ignore this setting)
This setting will switch off Aux-Relay1 if the RMS value of • AC IN voltage is too low for a
certain time (E2-11).
This AC level is determined by the • AC IN Low Disconnect (B2-01) setting.
Use this setting (E2-11) to disable re-starting of a generator which is switched off by •
hand when the Aux-Relay 1 is used to generate a start signal for that generator.
E2-12: No Temp. Alarm Select (When E2-13=0, ignore this setting)
E2-13: No Temp. Alarm for ? sec
If you want to switch off the Aux-Relay 1 when there is no over temperature alarm, this •
setting (E2-12) can be used to choose between pre-alarm or normal alarm.
As with other Aux-Relay 1 setting, a delay value must be specified also. This can be •
done with the Delay value for set Aux-Relay 1 OFF when No Overtemperature Alarm
66


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vetus COMBI1512 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vetus COMBI1512 in the language / languages: English as an attachment in your email.

The manual is 4,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vetus COMBI1512

Vetus COMBI1512 Usermanual and installation guide - Dutch - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info