661546
65
Zoom out
Zoom in
Previous page
1/80
Next page
Battery charger / inverter COMBI-GAMMA
090138.02 65
(E1-13) can be used to choose between pre-alarm or normal alarm.
As with other Aux-Relay 1 settings, a delay value (E1-14) must be specified also. This •
can be done with Delay value for set Aux-relay 1 ON when low battery alarm (E1-14)
setting.
E1-15: OverLoad Alarm Select (When E1-16=0, ignore this setting)
E1-16: OverLoad Alarm for ? sec
If you want to switch on the Aux-Relay 1 when there is a overLoad alarm, this setting •
(E1-15) can be used to choose between pre-alarm or normal alarm.
As with other Aux-Relay 1 setting, a delay value (E1-16) must be specified also. This can •
be done with Delay value for set Aux-Relay 1 ON when overload alarm (E1-16) setting.
E1-17: Udc Ripple Alarm Select (When E1-18=0, ignore this setting)
E1-18: OverLoad Alarm for ? sec
If you want to switch on the Aux-Relay 1 when there is a battery voltage ripple alarm. •
This setting (E1-17) can be used to choose between pre-alarm or normal alarm.
As with other Aux-Relay 2, setting a delay value (E1-18) must be specified also. This •
can be done with Delay value for set Aux-Relay 1 ON when battery voltage ripple alarm
(E1-18) setting.
E2 Group (Setting Aux-Relay 1 OFF Condition)
E2-01: Load Lower than ? Amps
E2-02: Load Lower for ? sec
Use these settings to switch Aux-Relay 1 OFF. When the actual AC OUT Load is below a •
certain value (E2-01) for a certain time (E2-02).
The corresponding • Aux-Relay ON condition is
E1-01: Load Higher than ? Amps and
E1-02: Load Higher for ? sec.
Note: If setting E2-02 (E1-02)=0 sec (Initial setting), then the E2-01 (E1-01) is ig-*
nored.
E2-03: Udc Lower than ? Voltage
E2-04: Udc Lower for ? sec
Use these settings to switch off the Aux-Relay 1 when battery voltage becomes lower •
than a certain limit (E2-03) for a certain time (E2-04)
Note: If E2-04=0 sec (Initial Setting), then E2-03 is ignored.*
E2-05: Udc Higher than ? Voltage
E2-06: Udc Higher for ? sec
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vetus COMBI1512 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vetus COMBI1512 in the language / languages: English as an attachment in your email.

The manual is 4,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vetus COMBI1512

Vetus COMBI1512 Usermanual and installation guide - Dutch - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info