815509
22
Zoom out
Zoom in
Previous page
1/64
Next page
2222 3-90-30007474Vermont Castings • Intrepid DV-IFT Owner’s Manual_R28 • 11/23
Figure 3.20 - Locate vent opening. NOTE: Zero clearance sleeve
isrequiredforcombustiblewallinstallations.
VO584-100a
Vent Opening
7/07 djt
10"
(254 mm)
10"
(254 mm)
7¹⁄₂" Dia.
(190 mm)
Framing Detail
VentOpening-CombustibleWall
VentOpening-NoncombustibleWall
Figure 3.21 - Intrepid minimum horizontal rear vent installation.
ST950
install pipe thru wall
7/07
18-1/4"
(464 mm)
to
Center of
Opening
Firestop
Wall Plate
10” x 10” (254 x 254 mm)
Wall Opening
Zero Clearance
Sleeve - Seal
Around
Seal Around
Terminal All Components Must
Remain Concentric
ZCS103
Zero Clearance Sleeve
& Firestop
12/6/99 djt
12”
(305mm)
Max. Length Sleeve
#8 Sheet Metal
Screws
Firestop
Figure 3.22 - Assemble the wall sleeve and restop.
3. Install the Wall Firestop/Sleeve assembly into the wall
cutout and fasten the restop to the wall cutout framing
members, Figure 3.22.
NOTES:
1. Twist-lock procedure: Line up locking lugs on male and
female ends of pipe sections. Insert the male end of pipe
into the female end until the locking lugs are covered.
Twist the female end clockwise an eighth of a turn to lock
sections together, Figure 3.24. Screws are not required
to secure the joint, but are acceptable provided they do
not penetrate the inner wall of the vent pipe.
4. Slip the wall cover over the interior end of the horizontal
pipe and install into the zero clearance sleeve. Seal the
joint inside the wall plate if needed to keep cold air from
being drawn into the home.
5. Install the vent terminal, Figure 3.21. Guide the inner and
outer vent termination collars into the adjacent pipes.
Double check that the vent pipes overlap the collars by 2”.
Fasten the termination to the outside wall with the screws
provided, and caulk the joint with weatherproof sealant.
6. Use wall straps to support vertical pipe runs at 8’ (2.4 m)
intervals.
Horizontal Installation
Step 1 - Set the gas appliance in its desired location. Check
to determine if wall studs or roof rafters are in the way once
the venting system is attached. If this is the case, you may
want to adjust the location of the appliance.
Step 2 - DirectVent Pro pipe, SLP pipe and ttings are
designed with special twist-lock connections. To connect
the venting system to the appliance ue outlet, a twist-lock
appliance adaptor is built into the appliance at the factory.
Assemble the desired combinations of black pipe sections
and elbows to the appliance adapter with pipe seams
oriented towards the wall or oor, as much out of view as
possible, Figure 3.23.
St976
simp pipe
8/07
Figure 3.23
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vermont Castings Intrepid - Gas at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vermont Castings Intrepid - Gas in the language / languages: English as an attachment in your email.

The manual is 17.23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info