Manual Vermont Castings Intrepid - Gas (page 24 of 64) (English)

815509

Zoom out

Zoom in

1/64

2424 3-90-30007474Vermont Castings • Intrepid DV-IFT Owner’s Manual_R28 • 11/23

IMPORTANT: You must attach the four (4) pieces of the

new vinyl siding stando󰀨 to the horizontal termination

cap in specic order to ensure a weather tight t. Loosely

assemble the four parts, in order, around the base of the

horizontal termination cap. Place the rst of four pieces

along the upper edge of the cap, then using two (2) screws

per side, secure each piece to the pre-drilled holes along

both sides of the cap, nally, attach the nal piece to the

bottom edge of the cap. Tighten all screws and mount cap,

with all four (4) pieces attached, directly onto the wall with

the four (4) 2-1/2" (64 mm) screws provided, Figure 3.29.

ST982

simp vinyl sidind

8/07

Cut Back

Siding 4 pc. Vinyl Siding

Stando󰀨

Wood Screws

(4 Req.)

Wood Screw

Figure 3.29

NOTES:

1. The four (4)

wood screws

provided should

be replaced

with appropriate

fasteners for use

on brick, block,

concrete or other

types of sidings.

2. For buildings with

vinyl siding or

stucco, another

component must

be used between

the horizontal

termination cap

and the wall

surface. The vinyl

siding stando󰀨

prevents excessive heat from possibly melting the vinyl

siding material. Vinyl siding stando󰀨s are not required

with snorkels. For vinyl wall installations a 4-piece vinyl

siding stando󰀨 should be assembled and installed

between the horizontal termination cap and the exterior

wall, Figure 3.29. The vinyl should be cut away to the

outer edges of the assembled stando󰀨.

HOT

ST981

SIMP termination

8/07

Wood

Screws

Figure 3.28

Step 6 - Slide the wall thimble cover up to the wall surface

and attach to the wall with screws provided, Figure 3.31.

Apply optional decorative brass trim to wall thimble cover

if desired.

Vertical Installation

Step 1 - Check these installation instructions for required

clearances (air spaces) to combustibles when passing

through ceilings, walls, roofs, enclosures, attic rafters or

other nearby combustible surfaces. Do not pack air spaces

with insulation. Check these instructions for maximum

vertical rise of the venting system and any maximum

horizontal o󰀨set limitations.

Figure 3.30

ST983

wall thimble cover

8/07

Sheet Metal

Screws

Wall Thimble Cover

Zero Clearance

Wall Sleeve

Firestop

3. When penetrating through stucco wall, install the counter

ashing. The counter ashing allows stucco, or other

materials, to be nished directly to the sides of the

termination cap. First attach the counter ashing to the

base of the horizontal termination cap with the small

screws provided, then mount entire assembly onto the wall

with the four (4) 2-1/2" (64 mm) wood screws provided.

Step 4 - Before connecting your horizontal pipe sections to

the horizontal termination cap, slide the wall thimble cover

over the pipe section nearest the interior side of wall, Figure

3.14.

Step 5 - Slide the appliance and vent assembly towards the

wall, carefully inserting the pipe section into the cap assembly.

It is important the pipe section extends into the back of the

termination cap with a minimum overlap of 1-1/4" (32 mm).

Use the two (2) sheet metal screws provided to secure the

pipe section to the back of the termination cap. The wall

thimble cover will cover the screw heads, Figure 3.30.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vermont Castings Intrepid - Gas in the language / languages: English as an attachment in your email.

The manual is 17.23 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vermont Castings Intrepid - Gas Manual

Product: