815509
21
Zoom out
Zoom in
Previous page
1/64
Next page
2121 3-90-30007474Vermont Castings • Intrepid DV-IFT Owner’s Manual_R28 • 11/23
When planning your installation, it will be necessary to
select the proper length of vent pipe for your particular
requirement. For horizontal installations, check these
instructions to determine the minimum clearance from
the rear of the appliance to the wall. It is also important to
note the wall thickness. Select the amount of vertical rise
desired or required, for “vertical-to-horizontal” installations
(verify that it is within the minimum and maximum limits.
To determine the length of vent pipe required for vertical
installations, measure the distance from the appliance ue
outlet to the ceiling, the ceiling thickness, the vertical rise in
an attic or second story, and allow for su󰀩cient vent height
above the rooine. For multi-story applications, restops
are required at each oor/ceiling level. If an o󰀨set is needed
in the attic, additional pipe and elbows will be required.
Figure 3.17
ST973
simpson rear install
8/07
Pipe Section
Round Ceiling Support
/ Wall Thimble Cover
Square Horizontal
Termination
Firestop
Zero Clearance Wall Sleeve
Figure 3.18
ST974
simpson thru
the wall
8/07
Square Horizontal
Termination Cap
Round Ceiling
Support / Wall
Thimble Cover
Pipe Section
90° Elbow
Pipe Section
90° Elbow
Firestop
Zero Clearance
Wall Sleeve
Rear Vent
Use components listed under "Approved Vent System
Components" under ‘Basic Straight through-the-Wall
Installation’ for an installation where the heater is parallel to
the wall and the vent system extends straight back through
that wall.
1. Locate the vent opening on the wall. Refer to Figures 3.20
& 3.21 to determine the top of the opening centerline. It
may be necessary to rst position the stove and measure
to nd the hole location. Depending on whether the wall
is made of combustible materials, cut the opening to the
size shown in Figure 3.20. Combustible wall openings
must be framed as shown in Figure 3.20.
2. Measure the wall thickness and cut the zero clearance
sleeve sections to proper length (MAXIMUM 12”).
Assemble the sleeve with the #8 sheet metal screws
supplied. Attach the restop plate to the sleeve end with
the holes, Figure 3.22. NOTE: The zero clearance sleeve
is required in combustible walls only.
ST975
simpson
straight up
8/07
Vertical
Termination Cap
(shown)
Storm Collar
Roof
Flashing
Ceiling Firestop
Round Ceiling
Support / Wall thimble
Pipe Section
Cathedral Ceiling
Support Box
90°Elbow
Figure 3.19
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vermont Castings Intrepid - Gas at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vermont Castings Intrepid - Gas in the language / languages: English as an attachment in your email.

The manual is 17.23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info