815502

Vermont Castings Dauntless FlexBurn Manual

15
Zoom out
Zoom in
Previous page
1/28
Next page
Vermont Castings • Dauntless FlexBurn Owner’s Manual_R17 • 2020 - ___ • 09/23 153-90-586000C
Keep Your Stove Looking New and Working Its Best
Letthereinthestovegooutandallowthestovetocool
completely before beginning any maintenance procedure.
This wood appliance needs periodic inspection and repair for
properoperation.Itisagainstfederalregulationstooperate
this wood appliance in a manner inconsistent with operating
instructions in this manual.
Care of the Cast Iron Surface
An occasional dusting with a dry rag will keep the painted
cast iron of your Dauntless FlexBurn® looking new.
The stove’s paint can be touched up as needed. First, mask
the areas, such as enameled parts, glass, or handles, around
the spot to be painted. Clean the spot with a wire brush.
Removethegriddleandsetitaside.Itisnormalforthegriddle
todarkenafteruse.Youcancleanitwithane-bristlewire
brush, or steel wool.
Then, touch up the stove with high temperature stove paint.
Apply the paint sparingly; two light coats of paint are better
than a single heavy one.
Care of the Porcelain Enamel Surface
Use a dry or slightly damp rag or soft brush to remove spills
orstains.Fordi󰀩cultjobsthatrequireacleaningagent,use
only a kitchen appliance cleaner or polish recommended for
use on enamel surfaces.
Ifporcelainenamelbecomeschippedor scratchedduring
use,apply“enamelepoxy”tothedamagedareaandallow
todry.Oncetheepoxyhasdried,sandtheareatoblendwith
surroundingareaandapplyappropriatecolortouch-uppaint.
Allow to dry completely before operating stove.
A. Cleaning the Glass & Replacement
Mostofthecarbondepositsontheglasswillburno󰀨during
hotres.
However, the ash residue that accumulates on the glass
surface should be removed regularly to prevent etching. To
clean the glass, follow this procedure:
• Be sure the glass is completely cool.
• Clean the glass with water or a cleaner made especially for
this purpose. Do not use abrasive cleaners. Use cleaning
agentssparinglyandbesuretokeepthemo󰀨theouter
surfaces of the stove.
• Rinse the glass thoroughly.
• Dry the glass completely.
Replace Broken Glass Immediately
Do not operate your stove if the glass in the doors is damaged.
Ifyouneedtoreplacetheglass,useonlythehightemperature
5 mm ceramic glass supplied by Vermont Castings. Do not
use substitutes.
3 3 Maintenance
Figure 3.2-Explodedviewoftheglassassemblyfortherightdoor.
10-24x1/4”(4)
Glass Panel
Gasket
Right Door
GlassClips(4)
2. Place the doors face down on a padded work surface. Be
especially careful with enameled doors.
3. Remove the screws that hold the glass retainer clips in
place, and remove the clips.
4. Carefully lift the broken glass panel from the door.
Installing the Glass
Check the gasket around the window; it should be soft and
resilient so that the glass will seal properly against the door.
Replace the gasket if it has hardened or if it is compressed.
1. Center the glass on the gasket.
2. Secure the glass on both doors with the retainer clips.
Tighten all screws, Figure 3.2.
3. Replace the doors on the stove.
4. Openandclosethedoorstocheckthattheytandwork
properly. Adjust as necessary.
Figure 3.1
(4)1/4-20
Bolts
Removing the Glass
1. Removetherightandleftdoorassembliesbyremoving(4)
1/4-20boltslocatedinsidethedooropening,Figure3.1.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vermont Castings Dauntless FlexBurn at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vermont Castings Dauntless FlexBurn in the language / languages: English as an attachment in your email.

The manual is 8.21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vermont Castings Dauntless FlexBurn

Vermont Castings Dauntless FlexBurn User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info