488163

Venga VG SIS 2 Manual

11
Zoom out
Zoom in
Previous page
1/56
Next page
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced
and folded in order to obtain a booklet A5 (+/- 148.5 mm
width x 210 mm height). When folding, make sure you
keep the good numbering when you turn the pages of
the I/B. Don’t change the page numbering. Keep the
language integrity.
11
VG SIS 2 - 101214
Assembly page 11/56
Fax +32 2 359 95 50
Do not use the iron if it has fallen, if it shows any visible signs of damage or if it leaks.
When you place the iron on its support (if available with the model), make sure that the
surface on which you put it is stable.
Proceed the same way if the water tank stops working or is damaged. To avoid the risk of
electric shock, do not disassemble the iron or steam tank, take it to a qualified technician
for examination and repair. Incorrect re-assembly can cause a risk of electric shock when
the iron or steam tank is used.
Fully unwind the main cord and supply hose before starting to iron.
The power switch should always be put in position “0” before plugging or unplugging the
power cord from outlet.
Unplug the appliance and allow the iron and the water tank to cool down before
cleaning or storing them and for pressurized steam iron station (depending on the model)
before opening, filling or emptying the water tank.
FOR PRESSURIZED STEAM IRONING STATION (DEPENDING ON THE MODEL), NEVER OPEN THE
CAP OF THE STEAM TANK WHILE THE APPLIANCE IS CONNECTED TO THE MAINS WALL SOCKET
AND ESPECIALLY WHEN STEAM IS BEING PRODUCED.
(*)
Competent qualified service: after sales department of the producer or importer or any
person who is qualified, approved and competent to perform this kind of repairs in order to
avoid all danger. In any case you should return the appliance to this service.
BEFORE THE FIRST USE
• We recommend cleaning the iron before the first use as follows: fill the water tank, put the
temperature dial on position “LINEN” and the steam regulator on MAX and let the iron
heat for 10 minutes. When the temperature has been reached, take the iron from the
base, hold it vertically and keep the steam button pressed for 30 seconds, then wait 30
seconds and repeat this cycle twice.
• Switch off the appliance (switch in position “0”), unplug it and let it cool down sufficiently,
then clean the soleplate with a damp cloth.
STEAM IRON: PRECAUTION FOR USE AND TEMPERATURES
• Always check first if a label with ironing instructions is attached to the article that needs to
be ironed. Follow these ironing instructions in all cases.
• If ironing instructions are missing but you know the kind of fabric, then see the table for
recommended ironing temperatures.
Kind of textile Temperature dial Steam ironing
Nylon
Synthetic (e.g. acetate,
acrylic, viscose,
polyamide, polyester, …)
Silk
MIN
NO
Wool

YES
Cotton
Linen

MAX
YES
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Venga VG SIS 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Venga VG SIS 2 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info