622291
11
Zoom out
Zoom in
Previous page
1/67
Next page
When measuring DC offset of an AC voltage, measure the AC voltage first and
select a range for the DC offset equal to or higher than the AC range to increase
accuracy.
7.2 Resistance measurements
Do not perform resistance measurements on live circuits.
Connect the red test lead to the "VΩ Hz " jack and the black lead to the
"COM" jack.
Set the rotary switch to ". When necessary, press the SELECT button until
is shown on the display.
Press the RANGE button to manually select the range.
Connect the test probes to the source being measured.
The measured value appears on the LCD display.
Notes:
o Never perform resistance measurements on a live circuit and make sure all
capacitors are completely depleted.
o To increase accuracy when measuring low resistance values, first hold the tips
of the measuring probes together to determine the resistance value of the test
leads. Subtract this value from the measured value of the circuit.
o For resistance measurements above 10MΩ the meter needs a few seconds to
stabilize the read-out.
o Should the measured resistance exceed the current range or in case of an open
circuit, the display will show “OL”.
7.3 Continuity measurements
Do not perform continuity measurements on live circuits.
Connect the red test lead to the "VΩ Hz " jack and the black lead to the
"COM" jack.
Set the rotary switch to .
Press the SELECT button to select continuity test .
Connect the test probes to the source being measured.
When the measured resistance is less than 40Ω a continuous beep is produced
and the resistance value is showed on the display. Should the measured
resistance exceed the current range or in case of an open circuit, the display will
show “OL”.
Nota: Never perform continuity measurements on a live circuit and make sure all
capacitors are completely depleted.
7.4 Diode measurements
Do not perform diode measurements on live circuits.
Connect the red test lead to the "VΩ Hz " jack and the black lead to the
"COM" jack.
Set the rotary switch to .
Press the SELECT button to select diode test .
Connect the red test probe to the anode of the diode and the black test probe to
the cathode.
The meter shows the forward voltage drop of the diode. When the diode is
connected with a reversed polarity, the display shows “OL”.
Notes:
o Never perform diode measurements on a live circuit and make sure all
capacitors are completely depleted.
o Measuring diodes that are part of a circuit might produce faulty results.
Consider unmounting from the circuit.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Velleman DVM4100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Velleman DVM4100 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 1,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info