557352

Tusa Buoyancy Compensator Jacket Manual

7
Zoom out
Zoom in
Previous page
1/12
Next page
12 13
GB
3. Place the required amount of weight in the weight cartridge. [Up to 4 kg can be
loaded in a single side.] (Fig. 26)
4. After inserting the weight, securely close the surface fastener. (Fig. 27)
5. After putting on the BCJ, insert the weight cartridge holders as shown in Fig.28. Be
sure to insert the cartridge. Having a diving buddy help will make it easier to insert
the weights.
(Fig. 27) (Fig. 28)(Fig. 26)
LOADING THE WEIGHTS (ex. BCJ-2100, 1800, 1650)
Except for the BCJ-2100 and 1650 are equipped with a weight loading system. The
weight loading system loads weights to optimize the balance of the BCJ in the water.
Use the following procedure to load weights.
The photographs were specially made to use for the explanation. When actually
loading the weights, please do so after setting the BCJ on the tank. Loading the
weights before putting the BCJ on the tank could make it difficult to set the BCJ on the
tank because of the weight.
1. Firmly grasp the weight release knobs located under the unit’s right and left
pockets. (Fig. 23)
2. Pulling the knob will release the safety lock. For safety you will feel the weight
cartridge catch a little bit, however just continue to pull it out of the holder. (Fig. 24
and 25)
(Fig. 24)
(Fig. 25)(Fig. 23)
7. Grasp belt end firmly and pull buckle to closed position. (Fig. 21) Attach belt end to
Hock & Loop fastener. (Fig. 22)
8. Check that the tank belt is securely fastened to tank. Hold tank in place in an
upright position. Grasp backpack by upper carrying handle, and try to move
backpack up and down on tank. There should be no movement, if belt moves, has
not been adequately tightened.
9. To readjust to proper tightness:
(a) Remove belt end from Hock & Loop fastener, and cam buckle.
(b) Unthread belt from end slot only of cam buckle.
(c) Repeat step 5-8 above.
10. To remove backpack from tank after a dive:
(a) Remove belt end Hock & Loop fastener, and open cam buckle.
(b) Unthread belt from end slot only of cam buckle.
(c) Slide backpack off tank.
WARNING: Proper installation and adjustment are extremely important to assure correct
performance of backpack. Improper installation on tank may allow the tank to slip out of
backpack. Loss of the tank could result in loss of buoyancy control, and/or air supply and
personal injury could result. If you have any questions about proper use for this product, ask
your diving instructor, your TUSA dealer, or your TUSA distributor.
(Fig. 22)(Fig. 21)
6. Pull the buckle to be upright positioned as shown in Figure 19 so the belt cannot
slip. And release the Hook and Loop fastener then thread the end of belt through
end slot of buckle. (Fig. 20)
(Fig. 20)(Fig. 19)
BCJ(CE)002-021 GB 10.11.17 9:35 AM ページ 12
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tusa Buoyancy Compensator Jacket at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tusa Buoyancy Compensator Jacket in the language / languages: English as an attachment in your email.

The manual is 1,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info