Manual Tunturi GO Treadmill 10 (page 10 of 52) (English, German, Dutch, French)

615563

Zoom out

Zoom in

1/52

OWNER’S MANUAL

•

GO RUN !0

to the right, turn the right adjustment

bolt 1/4 turn clockwise and the left

adjustment bolt ¼ turn anti-clockwise.

• If the belt remains centered the

adjustment is correct. If not, continue

to make small adjustments as above

until the belt is correctly aligned.

If the belt is allowed run across to

one side for long periods of time the

edges of the belt may be damaged

and the treadmill may not continue to

operate correctly. Any damage to the

belt caused by the lack of necessary

adjustment will not be covered by the

warranty.

ADJUSTING THE BELT TENSION

The belt must be tensioned if it begins

to slip on the rollers. In normal use,

however, keep the belt as loose as

possible! The belt tension is adjusted

by turning the same screws as used for

aligning the running belt. If turning the

screws will not effect the belt tension,

please contact your local Tunturi dealer.

• Increase the treadmill’s speed to 5

km/h (3 mph).

• Turn both adjustment screws an

equal amount, ¼turn clockwise.

• Try to slow the belt down by holding

onto the handrails and braking as

you walk (as if you were walking

downhill). If the belt slips, turn

another 1/4 turn and repeat the test.

When braking heavily the belt may

slip. If the belt keeps slipping despite

repeated adjustments, please contact

your local Tunturi dealer.

MALFUNCTIONS

NOTE!

Despite continuous quality control,

defects and malfunctions caused by

individual components may occur

in the equipment. In most cases it’s

unnecessary to take the whole device

Lubricate the running deck according

to the following instructions:

• Attach the nozzle of the lubrication

tube to the T-Lube S container.

• Lift the running deck and lock it.

• Position the nozzle between the belt

and the board. Try to reach the spray

as far into the center of the running

deck as possible.

• Spray the lubricant for 2-3 seconds.

• Lower the running deck into its

normal position. Use treadmill for

your training session. Or allow the

treadmill to run for at least 5 minutes.

NOTE!

Lubricate your treadmill only with T-Lube

S silicon lubricant. Contact your local

Tunturi distributor for further supplies

of T-Lube or further information on

lubrication and maintenance.

ALIGNING THE RUNNING BELT

Monitor belt tracking during exercise and

make adjustments as needed. The belt

should run in the center of the treadmill.

Alignment is not usually needed,

provided

• The treadmill is placed on an even,

solid and horizontal surface and the

belt is correctly tensioned

• The alignment of the belt is correct

It is, however, possible for the belt to

be pushed to one side due to the user’s

running style (e.g. more weight on

one foot). The alignment of the belt is

adjusted by turning the two bolts at the

back of the treadmill.

Align the belt according to the

following instructions

• Turn the power switch on and

increase the treadmill’s speed to 5

km/h (3 mph).

• If the belt drifts to the left, turn the left

adjustment bolt 1/4 turn clockwise

and the right adjustment bolt 1/8

turn anti-clockwise. If the belt drifts

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Tunturi GO Treadmill 10 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Tunturi GO Treadmill 10 Manual

Product: