631208

Truma Ultrastore Rapid GE Manual

8
Zoom out
Zoom in
Previous page
1/16
Next page
Manufacturer’s terms of warranty
1. Case of warranty
The manufacturer grants a warranty for malfunctions in the
appliance which are based on material or production faults.
In addition to this, the statutory warranty claims against the
seller remain valid.
A claim under warranty shall not pertain:
for parts subject to wear and in cases of natural wear
and tear,
as a result of using components in the units that are not
original Truma parts and using unsuitable gas pressure
regulators,
as a consequence of failure to respect Truma instructions
for installation and use,
as a consequence of improper handling,
as a consequence of improper transport packing,
use of water not compliant to Drinking Water Directive
98/83/EEC.
2. Scope of warranty
The warranty is valid for malfunctions as stated under
item 1, which occur within 24 months after conclusion of
the purchase agreement between the seller and the final
consumer. The manufacturers will make good such defects
by subsequent fulfilment, i.e. at their discretion either by
repair or replacement. In the event of manufacturers provid-
ing service under warranty, the term of the warranty shall not
re commence a new with regard to the repaired or replaced
parts; rather, the old warranty period shall continue to run.
More extensive claims, in particular claims for compensatory
damages by purchasers or third parties, shall be excluded.
This does not affect the rules of the product liability law.
The manufacturer shall bear the cost of employing the Truma
customer service for the removal of a malfunction under war-
ranty – in particular transportation costs, travelling expenses,
job and material costs, as long as the service is carried out in
Germany. Customer service carried out abroad is not covered
by the warranty.
Additional costs based on complicated removal and installa-
tion conditions of the appliance (e.g. removal of furniture or
parts of the vehicle body) do not come under warranty.
3. Raising the case of warranty
The manufacturer's address is:
Truma Gerätetechnik GmbH & Co. KG,
Wernher-von-Braun Strasse 12,
85640 Putzbrunn (Germany).
In Germany, always notify the Truma Service Centre if prob-
lems are encountered; in other countries the relevant service
partners should be contacted (see Truma Service Booklet or
www.truma.com). Any complaints are to be described in de-
tail. Please also specify the device serial number and date of
purchase.
In order for the manufacturers to be able to determine whether
an incident subject to guarantee has occurred, the end user
must, at his own risk, bring the device to the manufacturers or
send it to them. If there is damage to heaters (heat exchangers),
the gas pressure regulator must also be sent back to the factory.
In instances of the device being sent to the works, dispatch is
to be effected by freight transport. In cases under guarantee,
the works shall bear the transport costs or the costs of deliv-
ery and return. If the damage is deemed not to be a warranty
case, the manufacturer shall notify the customer and shall spec-
ify repair costs which shall not be borne by the manufacturer; in
this case, the customer shall also bear the shipping costs.
–
–
–
–
–
–
Declaration of conformity
1. Information about the manufacturer
Name: Truma Gerätetechnik GmbH & Co. KG
Address: Wernher-von-Braun-Str. 12, D-85640 Putzbrunn
2. Device identification
Type / model
LPG-water heater / Boiler Ultrastore Rapid GE (UGE 10)
3. Meets the requirements of the following Directives
3.1 Gas Appliances Directive 90/396/EEC
3.2 Low Voltage Directive 2006/95/EC
3.3 Radio Interference in Vehicles 72/245/EEC
(with the supplements), UN ECE R10
3.4 Electromagnetic Compatibility 2004/108/EC
3.5 End-Of-Life Vehicle Directive 2000/53/EC
3.6 Drinking Water Directive 98/83/EC
and bears the type approval numbers
e1 03 2604, E1 10R–03 2604
and the CE symbol with the CE product ident. no.
CE-0085CL0489.
4. Basis of the conformity assessment
2004/104/EC, 2005/83/EC, EN 89, EN 15033, EN 298 (partly),
DIN EN 60335-1:2010,
IEC 60335-1:2001 mod. +A1:2004 + A2:2006,
DIN EN 60335-2-21:2009,
IEC 60335-2-21:2002 mod. + A1:2004 + A2:2008,
DIN 2001-2, DVGW W270, KTW.
EN 55014-1, CISPR 14-1,
EN 61000-3-2, IEC 61000-3-2,
EN 61000-3-3, IEC 61000-3-3,
ISO 7637 Part 2, ISO 7637 Part 3,
EN 55014-2, CISPR 14-2, EN 13611 Type B,
EN 61000-4-2:2009, IEC 61000-4-2,
EN 61000-4-3, IEC 61000-4-3, EN 61000-4-4, IEC 61000-4-4,
EN 61000-4-5, IEC 61000-4-5, EN 61000-4-6, IEC 61000-4-6,
EN 61000-4-8, IEC 61000-4-8
5. Auditing body
DVGW, Federal Motor Transport Authority
6. Information and the function of the signatory
Signature: Dr. Andreas Schmoll
Managing Director / Engineering Putzbrunn, 10.01.2011
8
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Truma Ultrastore Rapid GE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Truma Ultrastore Rapid GE in the language / languages: English as an attachment in your email.

The manual is 1,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info