590214

Truma Mover XT Manual

26
Zoom out
Zoom in
Previous page
1/96
Next page
26
Electrical wiring and control unit
The Mover®XT / XT2 is only suitable for connection to 12 V
batteries (DC voltage).
Before commencing work, disconnect the battery and
any external electrical power supplies. If unsure about
the electrical connection, have the work performed by a quali-
fied vehicle electrician.
The electrical installation must comply with the technical
and administrative regulations of the respective country of
use (e.g. EN 1648-1). National regulations and rules must be
followed.
Connector cables for the drive motor and data cables are
pre-installed on each drive assembly. Mark the relevant motor
connecting cables (drive assembly A or B – see also connect-
ing diagram) and temporarily route them along the underbody
of the caravan to the location where it is planned to install the
control unit. An example of a suitable location for the control
unit is in a bed stowage box in close proximity to the manoeu-
vring system, at least 40 cm away from the battery.
Place the control unit in the stowage box and secure with the
chipboard screws provided (5 x 25).
At a distance of approx. 150 mm from the control unit con-
nection strip, mark a hole with a diameter of 25 mm on the
floor of the caravan through which to pass the wiring looms.
Before drilling, check for underlying frame sections, gas
lines and electrical cables.
Drill the hole and pass the cables through the floor of the
caravan to the control unit, routing them in such a way that
they cannot chafe (especially where they pass through metal
panels). Use the protection pipes provided to prevent damage
to cables.
The drive motors move when operating. In order to
compensate for this, secure the cables in this area
loosely with a little play to prevent the cables from being
stretched. No cable must be laid over the control unit.
Secure the cables to the chassis or underbody using the clips
and screws provided.
Seal the hole in the vehicle floor with plastic body sealant.
Connecting diagram
Installation in front of axle Installation behind axle
(seen from above) (seen from above)
A
B
A
B
Figure 30
PIN
(Fig. 31 / 32)
Description
Battery (C)
Battery + Battery + terminal, red 16mm
Battery - Battery - terminal, black 16mm
Drive assemblies in front of the axle
Motor left + (B) Motor left + terminal, red 10mm
Motor left - (B) Motor left - terminal, black 10mm
Motor right + (A) Motor right + terminal, red 10mm
Motor right - (A) Motor right - terminal, black 10mm
Drive assemblies behind the axle
Motor left + (A) Motor left + terminal, red 10mm
Motor left - (A) Motor left - terminal, black 10mm
Motor right + (B) Motor right + terminal, red 10mm
Motor right - (B) Motor right - terminal, black 10mm
Connector block (D)
K1-1 Safety socket, black
K1-2 Safety socket, black / red
K1-3 Data cable motor left, black 0.5mm
K1-4 Data cable motor left, black / red 0.5mm
K1-5 Data cable motor right, black 0.5mm
K1-6 Data cable motor right, black / red
0.5mm
K1-7 n. c.
K1-8 n. c.
K1-9 n. c.
K1-10 n. c.
Diagnostic interface (E)
J 1 Diagnostic interface
Installation in front of axle
+
-
B
A
+- +-
13 57 9
DE
C
M6 = 6 Nm
M5 = 3.5 Nm
Figure 31
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Truma Mover XT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Truma Mover XT in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish as an attachment in your email.

The manual is 11,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info