590214

Truma Mover XT Manual

24
Zoom out
Zoom in
Previous page
1/96
Next page
24
10. Short mounting system
Replacement for standard mounting system if this cannot be
used due to lack of space and to compensate for the height
(30 or 60 mm) of substructures such as tanks.
Part. no. 60031-20000
Figure 18
11. Mud guard set (no illustration)
Replacement for the standard mud guards, if these cannot be
adapted to the Mover®.
Part. no. 60031-08200
In some cases installation is not possible because of the
design of the sub-frame. Contact your dealer if necessary.
Detailed installation instructions are included with each
mounting set.
The vehicle frame must not be drilled (unless using the low
chassis kit* and the Eriba Touring mounting set) or welded.
Wheel suspension parts must not be removed under any
circumstances.
* In the case of the AL-KO Vario III / AV chassis, the vehicle
frame must under no circumstances be drilled into even if
the low chassis kit is used.
Selecting a location
The Mover®XT should preferably be mounted in front of the
axle, but in exceptional circumstances (e.g. lack of space) it
is also possible to mount it behind the axle. The Mover®XT2
should preferably be installed behind the axle Only use the
bolts provided (or the mounting parts available as special ac-
cessories) to attach the Mover®XT / XT2.
Mud guards
When a Mover® is fitted, the existing mud guards must be
moved / adapted if necessary (max. distance between tyre /
mud guard 300 mm).
If the original mud guards cannot be used, the Truma mud
guard set (part no. 60031-08200) must be used and adapted.
The mud guards are installed behind the axle. No mud
guards are required in front of the axle.
max. 200 mm
Driving direction
Mover
max.
300 mm
Mover® XT, XT2
Figure 19
Adapting the mud guards to the Mover®
1. Remove the mud guards.
2. Fit Mover® in accordance with the following installation
instructions.
3. Determine dimensions a and b and transfer to mud guards.
The top leg of the fastening bracket must face towards the
rear of the caravan.
Determining the cut-out sizes
a
b
Mover® XT / XT2
Mo
ver
®
X
T
2
XT / X
X
a
b
Mover® XT, XT2
Figure 20
Cut out the template on the last page of the installation in-
structions, place it onto the mud guard, transfer the contours
and cut out.
Pay attention to left and right sides!
If necessary, make recesses in mud guard for apron contour
and attach mud guard to underside of caravan 300 mm from
tyre.
Fitting the drive elements
The frame of the vehicle must be free of rust, grease and
heavy soiling. There must be no damage in the area of the
wheel suspension.
The wheels and tyres fitted on the caravan must be of the
same size and type, and must be inflated in accordance with
manufacturer's instructions.
Remove all components from packing and place on the floor.
Figure 21
In order to guarantee the validity of the general oper-
ating permit (ABE), the type plates (f) must be present
on the cross-strut on the right and left.
f
Figure 22
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Truma Mover XT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Truma Mover XT in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish as an attachment in your email.

The manual is 11,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info