590214

Truma Mover XT Manual

27
Zoom out
Zoom in
Previous page
1/96
Next page
27
Installation behind axle
+
-
A
B
+- +-
13 57 9
D
C
E
M6 = 6 Nm
M5 = 3.5 Nm
Figure 32
Once the cables have been routed out of the control unit, they
must be strain-relieved.
Connecting the drive motors
The data and motor cables must be routed together in such a
way that they cannot be torn off or damaged.
The cables may be shortened. Please pay attention to
different ring eyelet sizes.
Release the cover of the control unit by applying lateral press-
ure to the latching lugs, and clamp the cables as shown in
the connecting diagram (red = positive, black = negative).
Please ensure that the connections are made properly. (Torque
M5 = 3.5 Nm / M6 = 6.0 Nm)
Connecting the battery
Liquid electrolyte batteries must be installed in a separate
box with ventilation leading to the outside. The fuse in the
positive lead must be connected outside the box. A separate
box is not required for gel or AGM batteries. Pay attention to
the battery manufacturer's installation instructions.
The outgoing lines from the terminals must be routed with a
gap between them until after the fuse in the positive lead.
+
-
+
-
Figure 33
Route the battery connector cables (only use the original
Truma cables supplied) to the control unit and attach them
securely using the clips and screws provided.
Figure 34
The battery connector cables must not be extended.
They must be routed separately from the motor cables,
and must not run over the control unit.
Route battery connector cables so that they do not chafe
(particularly at leadthroughs through metal panels). Use
suitable protective leadthrough bushing to prevent damage
to cables. Connect battery connector cables to the existing
battery terminals (red = positive, black = negative).
Incorrect polarity will destroy the electronics / control
unit
The connection to the control unit (as per the connecting dia-
gram) must be made in the order: nut, battery connection ring
eyelet, nut (torque M6 = 6.0 Nm).
Connect fuse in the positive lead (150A) near the positive ter-
minal of the battery.
Connecting the safety socket
Route the 2-wire cable provided (9m or 10m) with the flat
connectors through the socket holder (g) and the rubber
sleeve (h).
If necessary, open cover and push socket connection out of
socket housing (i).
Connect 2-wire cable with flat connectors to micro switch.
RD / BK
BK
Figure 35
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Truma Mover XT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Truma Mover XT in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish as an attachment in your email.

The manual is 11,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info