Manual Truma Mover Mover SR Version 2 (page 16 of 68) (English, German, Dutch, Danish, French, Italian, Spanish)

484645

Zoom out

Zoom in

1/68

Before commencing any work, read and observe the installa-

tion instructions carefully!

Please ensure that no metal chips or other contaminants get

into the controller during installation.

In the case of screws with sealants, steps must be tak-

en to ensure that the thread is free of grease / oil.

Intended use

The Mover® SR has been built for use with single-axis caravans

with a gross weight of up to 2000 kg.

The Mover® SR weighs approx. 34 kg with the cross

actuation device attached.

Check the towing load of your vehicle and the gross weight of

your caravan in order to establish whether they are designed

for the additional weight.

Approval

The Truma Mover® SR has design approval, and a general

operating permit (ABE) has been issued for Germany. Accept-

ance by a vehicle expert is not required (except when install-

ing the low chassis kit). The ABE must be kept in the vehicle.

The Mover® satisfies other requirements stated in the EG di-

rectives and standards (see declaration of conformity).

The technical and administrative regulations of the country in

which the vehicle is initially registered must be complied with

when the Mover® is being installed.

Any modifications to the unit, or the use of spare parts and

accessories that are important to the operation of the system

that are not original Truma parts and failure to follow the in-

stallation and operating instructions will cancel the warranty

and indemnify Truma from any liability claims. In addition to

this, the operational approval for the device will be cancelled.

Tools and facilities required

To install the unit you will need:

13 mm, 17 mm, 10 mm socket wrench, ring spanner or

open-jawed spanner

Torque wrench (5 – 40 Nm)

Cable cutter / Crimping tool

Power drill / screwdrivers / 25 mm hole cutter

Portable 2 tonne trolley jack and axle stands to suit

Appropriate lighting

Minimum installation dimensions

A distinction is made between L-profiled and U-profiled

chassis as shown in the illustration.

Caravan floor

L-profiile

U-profile

max. 20

–

Installation instructions

Manufacturer’s terms of warranty

1. Case of warranty

The manufacturer grants a warranty for malfunctions in the

appliance which are based on material or production faults.

In addition to this, the statutory warranty claims against the

seller remain valid.

A claim under warranty shall not pertain:

for parts subject to wear and in cases of natural wear

and tear,

as a result of using components in the units that are not

original Truma parts,

for gas pressure regulation systems as a result of damage

by foreign substances (e.g. oils, plasticisers) in the gas,

as a consequence of failure to respect Truma instructions

for installation and use,

as a consequence of improper handling,

as a consequence of improper transport packing.

2. Scope of warranty

The warranty is valid for malfunctions as stated under item 1,

which occur within 24 months after conclusion of the pur-

chase agreement between the seller and the final consumer.

The manufacturers will make good such defects by subse-

quent fulfilment, i.e. at their discretion either by repair or

replacement. In the event of manufacturers providing service

under warranty, the term of the warranty shall not recom-

mence anew with regard to the repaired or replaced parts;

rather, the old warranty period shall continue to run. More ex-

tensive claims, in particular claims for compensatory damages

by purchasers or third parties, shall be excluded. This does not

affect the rules of the product liability law.

The manufacturer shall bear the cost of employing the Truma

customer service for the removal of a malfunction under war-

ranty – in particular transportation costs, travelling expenses,

job and material costs, as long as the service is carried out in

Germany. The warranty does not cover customer service work

in other countries.

Additional costs based on complicated removal and installa-

tion conditions of the appliance (e.g. removal of furniture or

parts of the vehicle body) do not come under warranty.

3. Raising the case of warranty

The manufacturer‘s address is:

Truma Gerätetechnik GmbH & Co. KG

Wernher-von-Braun-Straße 12

85640 Putzbrunn, Germany

Always notify the Truma Service Centre or one of our author-

ised service partners if problems are encountered (see Truma

Service book or www.truma.com). Please describe you com-

plaint in detail and state the factory number of the device and

the purchase date.

In order for the manufacturer to be able to determine whether

an incident subject to guarantee has occurred, the end user

must, at his own risk, bring or send the device to the manu-

facturer. If there is damage to heat exchangers, the gas pres-

sure regulator must also be sent back to the factory.

Air conditioners:

To avoid transportation damage, the unit may only be sent to

the Truma Service Centre Germany or one of our authorised

service partners if agreed beforehand. Otherwise the sender

bears the risk for any transportation damage.

Please send all shipment to the factory as freight. In cases

under guarantee, the works shall bear the transport costs or

the costs of delivery and return. If the damage is deemed not

to be a warranty case, the manufacturer shall notify the cus-

tomer and shall specify repair costs which shall not be borne

by the manufacturer; in this case, the customer shall also bear

the shipping costs.

–

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Truma Mover Mover SR Version 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish as an attachment in your email.

The manual is 11,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Truma Mover Mover SR Version 2 Manual

Product: