Manual Truma BM 14 (page 17 of 68) (English, German, Dutch, Danish, French, Italian, Spanish)

489383

Zoom out

Zoom in

1/68

Boat water heater BM 10, BM 14

Liquid gas storage water heater

(special version BM 10 EL, BM 14 EL with additional electric

heating 230 V, 850 W)

Intended use

This appliance is designed for the installation in boats. It is al-

so suitable for the installa tion in caravans and mobile homes.

Other forms of use are also possible after con sultation with

Turma.

Installation and repair are only to be carried out by an

expert. Always read and follow the operating instructions

carefully prior to starting any work!

Non-compliance with installation instructions or

incorrect installation can result in endangerment

of persons and property.

Approval

Declaration of conformity

The Truma boat water heater model has been tested and ap-

proved through the DVGW and fulfils the EC gas applian ce

guidelines (90/396/EEC) as well as the associated EC guide-

lines. The CE Ident. No. is available for EU countries:

CE-0085AO0048

EC Type Approval

e1 032604

Regulations

Guarantee claims, warranty claims and acceptance of liability

will be ruled out in the event of the following:

modifications to the unit (including accessories),

modifications to the exhaust duct and the cowl,

failure to use original Truma parts as replacement parts and

accessories,

failure to follow the installation and operating instructions.

It also be comes illegal to use the appliance, and in some coun-

tries this even makes it illegal to use the vehicle.

Notes on installation in boats

Installation in boats must accord with the technical and

administrative provisions of the individual country of use

(e.g. EN ISO 10239 for boats). The national regulations and

directives (in Germany, for example, DVGW work sheet G 608)

need to be observed.

The “Guidelines for the Construction, Installation, Testing and

Operation of Liquid Gas Systems for Household Purposes

on Inland Waterways” (BGR 146) must be complied with in

Germany. According to these guidelines the liquid gas system

must be installed by an engineer who has been approved by

the inland waterways employer’s liability associations and

tested by experts belonging to these employer’s liability insur-

ance associations.

In other countries always observe the respectively valid

regulations.

–

Installation instructions

Notes on installation in vehicles

In-vehicle installations must comply with the technical and

administrative regulations of the respective country of use

(e.g. EN 1949 for vehicles). The national regulations and direc-

tives (e.g. DVGW work sheet G 607 in Germany) need to be

observed.

The relevant employer’s liability insurance association accident

prevention regulations must be observed in Germany for vehi-

cles used for commercial purposes (BGV D 34).

In other countries always observe the respectively valid

regulations.

For further details on the rules and regulations in the respec-

tive country of designation, please contact our agencies

abroad (see Truma Service Booklet or www.truma.com).

Choice of location

Always install the appliance and its exhaust duct in such a way

that it is always easily accessible for service work and can be

easily removed and installed.

Position the water heater in such a way that the exhaust dou-

ble duct can be routed to the wall or deck cowl the shortest

way possible and is protected against damage.

Mount the wall cowl and / or the deck cowl to an outside sur-

face that is as straight and smooth as possible. This outside

surface must be exposed to the wind from all sides and, if

possible, there should be no decorative elements or panels

here.

No water may be allowed to penetrate the unit via the cowl.

Fig. L

The wall cowl must be attached so that no tank supports or

tank ventilation openings are found within 500 mm (R). In ad-

dition, no air discharge apertures for the living area or window

openings may be located with 300 mm (R) of it.

When fitting the cowl within the marked area below or

next to a window that must be open, an electrical win-

dow switch (part no. 34000-85800) must be installed. The gas

unit must automatically switch itself off using the Truma auto-

matic shut-off facility if the window is opened (Accessories,

part no. 39050-00800).

Installation of the water heater

Fig. F

Place water heater on a suitable level surface. There must

always be easy access for operating the drai ning valve (2).

Screw draining valve (2) to the 10 mm pipe socket in such

a way that the valve handle is at right angles to the floor

surface. Screw en closed pipe socket for draining hose to the

valve outlet. Carry out draining directly to the outside or col-

lect in a con tainer.

If the drain-valve cannot be activated when mounted

directly, a copper pipe must be installed downwards for

extension purposes and screwed tightly using compressive

screw connections. No hose may be used!

Tightly screw water heater to the attachment straps

(fig. F + G: 1).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Truma BM 14 in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish as an attachment in your email.

The manual is 0,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Truma BM 14 Manual

Product: