Manual Trotec PMSS 10-220 (page 14 of 19) (English)

753919

Zoom out

Zoom in

1/19

14 EN

3-in-1 multi-functional sander PMSS 10-220

Oscillation rate selection

By use of the setting wheel for oscillation rate selection you can

change the oscillation rate at any time, even during operation of

the device. The required oscillation rate depends on the material

and the operating conditions and can be determined by way of

field-testing. For sanding harder materials such as wood or

metal we recommend a higher oscillation rate, for softer

materials e.g. non-ferrous metals and varnishes a low

oscillation rate is sufficient. The setting range covers 6levels:

1– MAX (14,000 – 24,000opm).

1. Turn the setting wheel(15) to the desired oscillation rate.

Connecting the power cable

1. Insert the mains plug into a properly secured mains

socket.

Operation

Tips and notes on handling the multi-function sander

General information:

• Only use sanding sheets which are approved for the device

used.

• Check the sanding plate for correct fit before every

application. The sanding plate must be firmly locked in

place in the flange.

• Before every application, make sure that you have selected

the correct sanding sheet for the intended use. A coarse

grit is suited for rough grinding, a fine grain size, on the

other hand, is more appropriate for fine and finish grinding.

• Do not process wood and metal using the same sanding

sheet.

• Only use intact, flawless sanding sheets. Damaged

sanding sheets could tear and cause damage to the

workpiece. Exchange sanding sheets in due time.

• Clamp the workpiece unless it is firmly and safely

positioned by its own weight.

• Do not overload the device so that it comes to a standstill.

• Keep the venting slots clear to prevent the motor from

overheating.

Sanding:

• The oscillation rate and grain size of the sanding sheet

define the removal rate and the surface finish.

• Always sand in parallel to the grinding path ensuring an

appropriate overlap.

• Do not apply excessive contact pressure. Increased

contact pressure leads to a greater wear of the device and

the sanding sheet.

• If the material's surface is untreated, start grinding with

coarse or medium grain size and finish off with a fine grit.

• Best use a coarse grain size (40 or 60 grit) for removing

paint and for rough grinding particularly raw wood. For

surface-grinding undressed or sawn timber use abrasive

belts of medium grit (grain size80, 100 or 120). Use a fine

grit (grain size180, 240 or 320) to smoothen and fine-

grind timber and surfaces coated with old paint as well as

for dry sanding untreated wooden surfaces.

• Avoid the accumulation of dust at the workplace, always

use a dust extraction system when grinding.

• Use the front or lateral edge of the sanding sheet on the

sanding plate to process poorly accessible spots.

• Use a dust extraction system when grinding off residual

paint. Paint residues might smelt and then smudge both

workpiece and sanding sheet.

• Switch the device on before applying it to the workpiece.

Once the grinding process is concluded, lift the device off

the workpiece before you switch it off.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PMSS 10-220 in the language / languages: English as an attachment in your email.

The manual is 2,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PMSS 10-220

Trotec PMSS 10-220 User Manual - German - 21 pages

Trotec PMSS 10-220 User Manual - Dutch - 20 pages

Trotec PMSS 10-220 User Manual - French - 20 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Trotec PMSS 10-220 Manual

Product: