753919
16
Zoom out
Zoom in
Previous page
1/19
Next page
16 EN
3-in-1 multi-functional sander PMSS 10-220
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
Troubleshooting tasks which require the housing to be opened
must only be carried out by an authorized specialist electrical
company or by Trotec.
Light smoke or odour is emitted during the first use:
This is not a fault. These phenomena disappear after a
brief runtime.
The device does not start:
Check the power connection.
Check the power cable and mains plug for damage. If you
notice damages, do not try to take the device back into
operation.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Check the on-site fusing.
Info
Wait for at least 10 minutes before switching the
device back on.
The sanding plate does not move although the motor is
running:
Make sure that there is no workpiece debris blocking the
drive. Remove the blockages, if any.
Check whether you have mounted a sanding plate that is
suitable for this device.
The sanding plate is loose:
Check whether you have mounted a sanding plate that is
suitable for this device.
Check the sanding plate for tight fit. If necessary, tighten
the screws.
If necessary, check the rubber pins in the sanding plate for
correct fit.
The motor slows down:
Check whether the device is overloaded by the workpiece.
Reduce the pressure applied on the workpiece.
Check whether the workpiece is suitable for the tasks to
be carried out.
The surface of the workpiece is not smooth or the grinding
performance is insufficient:
Check whether the selected sanding sheet is suitable for
the material to be processed.
If the sanding sheet is worn, replace it with a new one, see
chapter Changing the sanding sheet.
Check the oscillation rate setting. It must be suitable for
both the sanding sheet and the material.
Select a higher oscillation rate by turning the setting wheel
for the oscillation rate selection to the desired level.
The sanding sheet wears off quickly:
Check whether the selected sanding sheet is suitable for
the material to be processed.
Reduce the pressure applied on the workpiece.
Select a lower oscillation rate by turning the setting wheel
for the oscillation rate selection to the desired level.
The device becomes hot:
Make sure not to exert too much pressure on the device
during operation.
Select a lower oscillation rate by turning the setting wheel
for the oscillation rate selection to the desired level.
Check whether the selected sanding sheet is suitable for
the tasks to be carried out.
Keep the venting slots clear to prevent the motor from
overheating.
Wait for 10minutes before switching the device back on.
Note
Wait for at least 3 minutes after maintenance and
repair work. Only then switch the device back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to an authorised specialist electrical company or to
Trotec for repair.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PMSS 10-220 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PMSS 10-220 in the language / languages: English as an attachment in your email.

The manual is 2,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PMSS 10-220

Trotec PMSS 10-220 User Manual - German - 21 pages

Trotec PMSS 10-220 User Manual - Dutch - 20 pages

Trotec PMSS 10-220 User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info