753369
15
Zoom out
Zoom in
Previous page
1/20
Next page
EN 15
cordless pendulum action jigsaw PJSS 11-20V
3. Slide the rip fence(14) into the slot with the marking
pointing up.
4. Move the rip fence(14) into the desired position.
5. Tighten the locking screws(23).
6. Refit the battery(13; see Inserting the battery).
Adjusting the pendulum action
You can adjust the pendulum movement of the saw blade.
Levels 1 to 3 allows for a faster work progress and level0
(pendulum movement off) enables fine and clean cutting edges.
The ideal pendulum level for the respective application can be
determined by way of field-testing. Please observe the following
instructions:
If you want to obtain a fine and clean cutting edge,
preferably select a low pendulum level or switch off the
pendulum action completely.
Switch off the pendulum action when processing thin
materials.
Work at a low pendulum level when processing hard
materials.
For soft materials or when sawing wood with the grain you
can work with the maximum pendulum level.
1. Set the pendulum action selector switch(5) to the desired
level. The higher the level, the larger the pendulum stroke.
The pendulum action can also be adjusted during
operation.
I
II
III
0
5
Operation
Tips and notes on handling the jigsaw
General information:
Keep the venting slots clear to prevent the motor from
overheating.
Check the tool in the tool holder for proper fit before every
application. The tool must be firmly locked in place in the
designated holding fixtures in the tool holder.
Before every application, make sure that you have selected
the correct tool for the intended use.
Sawing:
Only use intact, flawless saw blades. Bent, blunt or
otherwise damaged saw blades could break.
When sawing lightweight construction materials, make
sure to observe the legal regulations and
recommendations of the material manufacturers.
Before sawing wood, chipboards, building materials etc.
with HCSblades, check the above for foreign objects, e.g.
nails, screws or similar. If required, remove the foreign
objects or use HSS saw blades.
Use a narrow saw blade when sawing tight curves.
The saw blade should not be longer than required for the
intended cut.
Switching the device on and off
Wear your personal protective equipment when working with
the device.
1. Check whether the fixed saw blade, the pendulum action
and the cutting angle are suitable for the intended
application.
2. Check whether the workpiece is secured and the worktop
prepared correspondingly.
3. Position the base plate with the sliding block(6) on the
workpiece.
4. Press the start lock(1) to be able to actuate the on/off
switch.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PJSS11-20V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PJSS11-20V in the language / languages: English as an attachment in your email.

The manual is 3,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PJSS11-20V

Trotec PJSS11-20V User Manual - German - 23 pages

Trotec PJSS11-20V User Manual - Dutch - 22 pages

Trotec PJSS11-20V User Manual - French - 21 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info