753369
17
Zoom out
Zoom in
Previous page
1/20
Next page
EN 17
cordless pendulum action jigsaw PJSS 11-20V
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.
If required, allow the device to cool down.
Remove the battery from the device (see Start-up chapter).
Clean the device according to the Maintenance chapter.
Store the device according to the Storage chapter.
Available accessories
Warning
Only use accessories and additional equipment
specified in the instructions.
Using insertion tools or accessories other than those
specified in the instructions may cause a risk of injury.
Designation Article number
Jigsaw blade set for wood, 10-piece 6.215.001.101
Jigsaw blade set for metal, 10-piece 6.215.001.131
Multiflex 20V 2.0Ah spare battery 6.200.000.303
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
Troubleshooting tasks which require the housing to be opened
must only be carried out by an authorized specialist electrical
company or by Trotec.
Light smoke or odour is emitted during the first use:
This is not a fault. These phenomena disappear after a
brief runtime.
The battery does not charge:
Check whether the battery is correctly connected to the
quick charger.
Slide the battery into the quick charger in a way that the
battery terminals engage in the quick charger. The battery
must lock in place in the quick charger.
Check the power connection.
Check the power cable and mains plug for damages.
Check the fuse (home).
Check the quick charger for damages. Should the quick
charger be damaged, stop using it. Contact the Trotec
customer service.
Check the battery terminals for dirt. Remove any dirt.
The battery might be defective and have to be replaced.
Only use batteries of the same type.
The device does not start:
The battery power might be too low. Recharge the battery.
Check whether the battery is correctly connected to the
device.
Slide the battery onto the device in a way that the battery
terminals engage. The battery must lock in place in the
device.
Check the battery terminals for dirt. Remove any dirt.
Info
Wait for at least 10 minutes before switching the
device back on.
The saw blade is loose:
Make sure that the saw blade is firmly locked in place in
the designated recesses of the quick-release chuck.
Make sure that the quick-release chuck is locked.
The saw blade experiences difficulties penetrating the
material to be processed or the sawing performance is
insufficient:
Check whether the pendulum action setting is suitable for
the material to be processed.
If the saw blade is worn, replace it with a new one.
Check whether the chosen saw blade is suitable for the
material to be processed.
The device becomes hot:
Make sure not to exert too much pressure on the device
during sawing.
Check whether the chosen saw blade is suitable for the
task to be carried out.
Keep the venting slots clear to prevent the motor from
overheating.
Info
Wait for at least 10 minutes before switching the
device back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to an authorised specialist electrical company or to
Trotec for repair.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PJSS11-20V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PJSS11-20V in the language / languages: English as an attachment in your email.

The manual is 3,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PJSS11-20V

Trotec PJSS11-20V User Manual - German - 23 pages

Trotec PJSS11-20V User Manual - Dutch - 22 pages

Trotec PJSS11-20V User Manual - French - 21 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info