753916
14
Zoom out
Zoom in
Previous page
1/20
Next page
14 EN
angle grinder PAGS 10-230
9. Retighten the clamping nut(15) by means of the pin-type
face wrench(16). Then let go of the spindle lock(1).
Pay attention not to damage the cutting disc.
15
16
1
10. Check the cutting disc(14) for proper fit.
11. Check whether the cutting disc can rotate freely. Make
sure that the disc does not touch the guard or any other
parts.
12. Carry out a test run of approx.1minute without load prior
to every disc change and every start-up in order to check
the cutting disc for correct fit.
Caution
If the disc is out-of-round, rotates unevenly, vibrates,
oscillates, or if unusual noises or sparks are generated,
the cutting disc must be exchanged immediately.
Otherwise, there is a risk of injury.
Connecting the power cable
1. Insert the mains plug into a properly secured mains
socket.
Operation
Tips and notes on handling the angle grinder
General information:
Carry out a test run of approx.1minute without load prior
to every disc change and every start-up in order to check
the cutting disc for correct fit.
Only use tools which are approved for the device used.
Before every application, make sure that you have selected
the correct tool for the intended use.
Check the tool in the tool holder for proper fit before every
application. The tool must be firmly locked in place in the
designated holding fixtures on the tool holder.
Check whether the cutting disc can rotate freely. Make
sure that the disc does not touch the guard or other parts.
Only use discs with a speed imprinted that is at least as
high as the speed indicated on the device's nameplate.
Clamp the workpiece unless it is firmly and safely
positioned by its own weight.
Do not overload the device so that it comes to a standstill.
After operation at high load, let the device run at idle for
several minutes to allow the tool to cool down.
Do not touch the discs until they have cooled down.
Keep the venting slots clear to prevent the motor from
overheating.
Cutting:
Only use intact, flawless cutting discs. Bent, blunt or
otherwise damaged cutting discs could break.
Never use the cutting disc for roughing!
Only advance moderately during operation and make sure
that the cutting disc does not get jammed.
Do not slow down the decelerating cutting disc by pressing
against the side of the disc.
Always move the cutting disc through the workpiece in
reverse rotation.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PAGS 10-230 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PAGS 10-230 in the language / languages: English as an attachment in your email.

The manual is 3,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PAGS 10-230

Trotec PAGS 10-230 User Manual - German - 22 pages

Trotec PAGS 10-230 User Manual - Dutch - 22 pages

Trotec PAGS 10-230 User Manual - French - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info