753916
16
Zoom out
Zoom in
Previous page
1/20
Next page
16 EN
angle grinder PAGS 10-230
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
Troubleshooting tasks which require the housing to be opened
must only be carried out by an authorized specialist electrical
company or by Trotec.
The only exception is the replacement of the carbon brushes
(see chapter Replacing the carbon brushes).
Light smoke or odour is emitted during the first use:
This is not a fault. These phenomena disappear after a
brief runtime.
The device does not start:
Check the power connection.
Check the power cable and mains plug for damage. If you
notice damages, do not try to take the device back into
operation.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Check the on-site fusing.
Info
Wait for at least 10 minutes before switching the
device back on.
The cutting disc is loose:
Check whether you are using a cutting disc that is suited
for this device.
Make sure that the mounting flange(13) is firmly locked in
place in the designated recesses.
Make sure that the cutting disc(14) sits flush on the
mounting flange(13) without clearance.
Make sure that the flat side of the clamping nut(15) rests
on the cutting disc(14).
The guard is loose:
Make sure that the coded projections(11) are firmly locked
in place in the designated groove.
Make sure that the locking lever(12) is folded in
completely.
If necessary, tighten the adjusting screw(10).
The cutting disc does not move although the motor is
running:
Make sure that the clamping nut(15) is firmly tightened,
see chapter Tool change.
Make sure that there is no workpiece debris blocking the
drive. Remove the blockages, if any.
Make sure that the cutting disc is not jammed in the
workpiece.
The motor slows down:
Check whether the device is overloaded by the workpiece.
Reduce the pressure applied on the workpiece.
Check whether the workpiece is suitable for the tasks to
be carried out.
Check whether the carbon brushes(19) are worn out. If
necessary, replace them; see chapter Changing the carbon
brushes.
The cutting disc experiences difficulties penetrating the
material to be processed or the cutting performance is
insufficient:
Check whether the chosen cutting disc is suitable for the
material to be processed.
If the cutting disc is worn, replace it with a new one.
The device becomes hot:
Check whether the cutting disc is suitable for the tasks to
be carried out.
Make sure not to exert too much pressure on the device
during operation.
Keep the venting slots clear to prevent the motor from
overheating.
Wait for 10minutes before switching the device back on.
Note
Wait for at least 3 minutes after maintenance and
repair work. Only then switch the device back on.
The device still does not operate correctly after these
checks:
Please contact the customer service. If necessary, bring the
device to an authorised specialist electrical company or to
Trotec for repair.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec PAGS 10-230 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec PAGS 10-230 in the language / languages: English as an attachment in your email.

The manual is 3,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec PAGS 10-230

Trotec PAGS 10-230 User Manual - German - 22 pages

Trotec PAGS 10-230 User Manual - Dutch - 22 pages

Trotec PAGS 10-230 User Manual - French - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info