689444

Trotec B500 Manual

27
Zoom out
Zoom in
Previous page
1/60
Next page
Operating Manual – Electronic Humidifier
EN
B - 7
identically coded to the one sensor, or of operating each
one independently, each with a separate sensor and
different codings. Please proceed as follows.
Procedure:
1. Carefully lift the cover of the radio sensor with a
small screwdriver and take it off.
2. Code the radio sensor by setting the slide control
with a small screwdriver.
3. Remove the housing of the B 500 air humidifier.
4. Loosen the four of screws on the top side of the con-
trol panel and lift it off.
5. Code the receiver circuit board on the rear side of
the control panel by setting the slide control with a
small screwdriver.
m The coding of the radio sensor and of the
receiver circuit board must match exactly
(note ON and OFF). Otherwise there is no
certainty that the system will function.
6. Close the cover of the radio sensor again.
7. Fasten the control panel down again with the four
screws and set the top part of the housing onto it.
8. Breathe lightly on the radio sensor to check the
functioning of the system
15. Fault code display
The B 500 Professional has an independent monitor-
ing system that gives you the possibility of spotting
errors quickly and reacting accordingly.
The fault display can be combined with an acoustic sig-
nal so that a „beep” can be heard in addition to the dis-
play being shown. You can select this setting yourself.
Please refer to the section on „Menu programming”.
The following fault codes tell you what problem has
occurred and what has to be done.
m If a fault code is displayed, only the On/Off
button and the PROG and SET key on the re-
mote control unit can be used.
Fault code Fault What to do?
01 Water tank is empty • Check water level and top up if necessary.
• Check water level diodes for dirt and clean if necessary.
• Has distilled water been used? If so, top up with plain tap
water.
• Check the diodes connection.
• Is the automatic water supply defective? (optional extra)
02 UV lamp defective • Replace UV lamp. (see „Changing the UV tube“)
03 Water leaking
(only possible with external
water sensor)
• Check whether the filter has been inserted correctly.
• Check whether the appliance is standing upright.
• Check whether the automatic water supply is working cor-
rectly (if fitted).
• Check tank for leaks.
04 Water tank overfilled
(only possible with automatic
water supply)
• Check the function of the magnetic valve.
• Check the water level diodes for dirt.
05 No radio signal from hygros-
tat. The receiver on the con-
trol panel has not received a
signal for a quite some time.
•Is the radio transmitter too far away from the appliance?
• Check the function and coding of the radio transmitter (see
„Starting up” / „Coding the radio sensor system”).
• Replace the batteries if necessary.
09 Several faults have occurred
simultaneously
• Check the appliance as described for Faults 01 to 04.
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec B500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec B500 in the language / languages: English, German, French as an attachment in your email.

The manual is 5,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info