798767

Traeger COM200 - Large Commercial Trailer Manual

14
Zoom out
Zoom in
Previous page
1/17
Next page
Still no Pellets in the Firepot – Proceed to step 3.
3) Disconnect Power Cord from electrical outlet.
a) Unplug the Auger Drive Motor ( Red/White wire pair connector) and the Draft
Induction Fan (Orange/White wire pair connector).
b) Reconnect the Draft Induction Fan to the Red/White wire pair and the Auger
Drive Motor to the Orange/White pair.
c) Plug Power Cord into an appropriate, grounded electrical outlet and turn the
Switch/Dial ON.
d) If the Auger Drive Motor is operating (check the small fan blade on the back of
the motor), the problem is in the Three Speed or Digital Control, which will need
to be replaced. Contact your Traeger Dealer or the Traeger Parts
Department (SECTION SEVEN) to place an order.
4) If the Auger Drive Motor is not operating but the Draft Induction Fan is operating,
the problem is in the Auger system, which will need to be checked.
a) With the Switch/Dial OFF, locate the small fan blade on the back of the Auger
Drive Motor.
b) While watching the fan blade, turn the Switch/Dial to ON. If the fan blade does
not turn, turn the Switch/Dial to OFF. This indicates a defective Auger Drive
Motor and it will need to be replaced. Contact your Traeger Dealer or the
Traeger Parts Department (SECTION SEVEN) to place an order.
c) If the fan blade turns a bit and then stops, continue watching and turn the
Switch/Dial to OFF. If the fan blade UNWINDS slightly, this indicates a jam in
the Auger system which will need to be cleared.
d) Disconnect Power Cord from electrical outlet and remove Pellets from the Pellet
Hopper. Check for foreign objects and wet/decomposed Pellets, both of which
can cause a jam in the Auger system. The Auger will need to be removed to
clear a jam in the Auger system. See “HOW DO I REMOVE THE AUGER IF IT
JAMS?” section below.
`
HOW DO I REMOVE THE AUGER IF IT JAMS?
For models with a fixed Auger Drive Motor:
1) Remove any covers necessary to access the Auger Drive Motor.
2) Remove the screw connecting the Auger Drive Motor shaft to the Auger shaft, using
a 7/64 hex wrench and a 5/16 wrench or driver.
3) Remove two bolts mounting the Auger Drive Motor/Bracket assembly to the Burner
Box with a 7/16 wrench.
4) With a small pipe wrench or locking pliers on the Auger shaft, turn the Auger counter
clockwise. It will turn hard until it breaks free, then the Auger will turn freely.
5) Remove the Auger and clean all Pellets, ash or foreign objects from the Auger,
Auger Tube and Firepot. A shop-vac is ideal tor this task.
6) Sand the outside surfaces of the auger with medium grit sandpaper. Check the
inside of the Auger Tube and sand it if needed. Vacuum sanding grit from the Auger
Tube and Firepot when finished.
7) Reinstall the Auger into the Auger Tube, making sure that it rotates freely.
8) Re-attach the Auger Drive Motor/Bracket assembly, ensuring that the Auger shaft
rotates freely on the Auger Drive Motor Shaft. Re-attach the Auger shaft to the
Auger Drive Motor shaft.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Traeger COM200 - Large Commercial Trailer at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Traeger COM200 - Large Commercial Trailer in the language / languages: English as an attachment in your email.

The manual is 0.74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info