798767

Traeger COM200 - Large Commercial Trailer Manual

15
Zoom out
Zoom in
Previous page
1/17
Next page
For models with a floating Auger Drive Motor:
(Note: some units with the floating Auger Drive Motor will require metric tools.)
1) Remove any covers necessary to access the Auger Drive Motor.
2) Remove the screw connecting the Auger Drive Motor shaft to the Auger shaft and
the screw retaining the Auger Bushing into the Auger Tube.
3) With a small pipe wrench or locking pliers on the Auger shaft, turn the Auger counter
clockwise. It will turn hard until it breaks free, then the Auger will turn freely.
4) Remove the Auger and clean all Pellets, ash or foreign objects from the Auger,
Auger Tube and Firepot. A shop-vac is ideal tor this task.
5) Sand the outside surfaces of the auger with medium grit sandpaper. Check the
inside of the Auger Tube and sand it if needed. Vacuum sanding grit out of the
Auger Tube and Firepot when finished.
6) Reinstall the Auger Bushing and the Auger into the Auger Tube, making sure that
the Auger rotates freely.
7) Re-attach the Auger shaft to the Auger Drive Motor shaft.
WHY DOES MY GRILL FIRE GO OUT ON “SMOKE” SETTING?
Excess ash in the Firepot may be the problem.
1) Open the Door and remove the Porcelain Grill, Grease Drain Pan and Heat Baffle
from inside the Grill.
2) IMPORTANT: Remove all unburned Pellets and ash from inside and around
the Firepot. A shop-vac is ideal tor this task CAUTION! ASSURE THAT THE
GRILL IS COLD TO AVOID A FIRE FROM HOT ASH.
3) Replace the Heat Baffle, Grease Drain Pan and the Porcelain Grill and initiate start-
up procedure.
4) If this didn’t remedy the problem, contact Traeger Technical Support (SECTION
SEVEN) for additional troubleshooting help.
THE AUGER MAKES A LOT OF NOISE WHEN I TURN THE GRILL ON AND I HAVE
NOTICED A DROP IN THE GRILL TEMPERATURE. WHAT CAN I DO TO CORRECT
THIS?
In Grill models with a fixed Auger Drive Motor, you will need to “TRUE” the Auger
1) Remove all Pellets from the Pellet Hopper and run Pellets out of the Auger Tube.
2) Remove the screw connecting the Auger Drive Motor shaft to the Auger shaft, using
a 7/64 hex wrench and a 5/16 wrench or driver.
3) Spin the Auger shaft over the Auger Drive Motor shaft. It should rotate freely, without
binding.
4) If the Auger shaft binds, loosen the two bolts mounting the Auger Drive
Motor/Bracket assembly to the Burner Box with a 7/16 wrench.
5) Move the Auger Drive Motor/Bracket assembly until you can feely rotate the Auger
shaft over the Auger Drive Motor shaft.
6) Re-tighten the 7/16 bolts, making sure that the Auger End Piece Shaft still freely
rotates over the Auger Drive Motor shaft.
7) Reinstall the screw and nut connecting the Auger Drive Motor shaft to the Auger
shaft.
… 15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Traeger COM200 - Large Commercial Trailer at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Traeger COM200 - Large Commercial Trailer in the language / languages: English as an attachment in your email.

The manual is 0.74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info