798767

Traeger COM200 - Large Commercial Trailer Manual

10
Zoom out
Zoom in
Previous page
1/17
Next page
SECTION TWO: INITIAL FIRING INSTRUCTIONS
(To be used on initial firing or anytime the Grill runs out of Pellets)
In order to ensure proper operation of the Grill, you must first
allow the Auger Tube to be “charged” with Pellets.
1) Open the Door and remove the Porcelain Grills, Grease Drain Pan and Heat Baffle
from inside the Grill.
2) Make sure the Switch/Dial is in the OFF position. Plug the Power Cord into an
appropriate, grounded electrical outlet.
3) Open the Pellet Hopper Lid and locate the Augers. Make sure there are no foreign
objects in the Augers. Turn the Switch/Dial ON and look into the Pellet Hopper to
confirm the Augers are turning. At the same time, place your fingers over the
Firepots and feel the air movement from the Draft Inducer Fans. Look to see if the
Hot Rods are getting hot. DO NOT TOUCH THEM! Turn the Switch/Dial OFF.
4) Fill the Pellet Hopper with TRAEGER BBQ PELLETS. WARNING! USE ONLY
TRAEGER BRAND BBQ PELLETS, which are specifically made to work in our
Grills. NEVER use heating fuel pellets in the Grill. Turn the Switch/Dial ON, set
the Temperature Dial to HIGH. Note: During the initial charging of the Augers, it will
take time for the Pellets to travel from the Pellet Hopper to the Firepots. When the
Pellets begin to fall into the Firepots, turn the Switch/Dial OFF.
5) Turn the Switch/Dial ON, set the Temperature Dial to SMOKE. Let the Pellets come
to full flame. Once you see flames come out of the Firepots, turn the Switch/Dial
OFF, and let the Grill cool down.
RECOMMENDATION for ease of clean-up: Line the Grease Drain Pan with
heavy-duty aluminum foil. Be sure the edges and ends of the foil are tight
against the bottom of the Grease Drain Pan. Position the Heat Baffle, the foil lined
Grease Drain Pan and Porcelain Grills in their proper locations.
6) With the Door open, turn the Switch/Dial ON and set the Temperature Dial to
SMOKE. In approximately 2 minutes you will notice whitish-gray smoke coming out
of the Grill as the Pellets ignite. After assuring the Pellets have ignited, close the
Door and set the Temperature Dial to any cooking setting desired.
7) Note: Before cooking the first batch of food in your new Grill, you will need to
season the Grill. Turn the Temperature Dial to HIGH and run for 45 minutes at
this setting with the Door closed. This must be done before cooking any food
on the Grill.
8) The Grill should be allowed to pre-heat for approximately 10 minutes with the Door
closed before placing food in the Grill.
ALWAYS START THE GRILL ON SMOKE SETTING
WITH THE DOOR OPEN
Once the Pellets are ignited, close the Door and
set the Temperature Dial to any cooking temperature desired.
NOTE: When operating this Grill, maintain a minimum
clearance of 10 inches from Grill to combustibles
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Traeger COM200 - Large Commercial Trailer at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Traeger COM200 - Large Commercial Trailer in the language / languages: English as an attachment in your email.

The manual is 0.74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info