671194

Tower T19005 Manual

9
Zoom out
Zoom in
Previous page
1/20
Next page
Safety and Instruction Manual
9
Helpline: +44 (0) 844 984 0055
MincingMeat:
1. Cut the meat into small enough chunks/
pieces to ensure it ts easily into the hopper
opening.
Note: It is recommended to use sinew free,
boneless and fatless meat, approximately sized
as: 20mm; 20mm and 60 mm.
2. Plug the unit in. Move the ON/OFF/REV
switch to the ON position.
3. Feed the produce into the hopper plate,
using the food pusher only.
4. When nished, switch the appliance off and
unplug it from the power supply.
ReverseFunction:
If jamming occurs switch the grinder off at the
plug. Move ON/OFF/REV switch to the REV
position, and turn the grinder back on.
This will reverse the ow of the product.
The worm will begin rotating in the opposite
direction, thus empting the horn of the grinder.
Disassembling:
1. Make sure the motor has come to a
complete stop.
2. Disconnect the plug from the power source.
3. Disassemble in the reverse order of
assembly.
4. Tip: To remove the cutting plate easily, place
a screwdriver between the cutting plate and
the horn, to lift it up and away.
5. Unscrew the fastening screw to remove the
horn.
MakingSausagewithyourMeatGrinder:
1. Untangle and place your casings into
groups.
2. Take each casing and wash both the inside
and outside, to get rid of any debris. Place
in lukewarm water.
3. Grind meat to your desired consistency.
4. Mix your seasoning in with the ground
meat.
5. Fit the worm into the horn. Place the
sausage stufng attachment on top and use
the xing ring to t everything into place.
(See below image for assembly).
6. Open one end of your casing using your
ngers and slip it over the end of the
sausage stufng attachment.
7. Slide the whole casing onto the sausage
stufng attachment, leaving around 2” of
casing overhanging the end.
8. Once in place, turn the Meat Grinder on,
and use the meat pusher to work the
sausage meat through the grinder and into
the casing.
9. Fill the sausage casing, guiding it with your
hands.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tower T19005 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tower T19005 in the language / languages: English as an attachment in your email.

The manual is 2,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info