485654
30
Zoom out
Zoom in
Previous page
1/42
Next page
58 59
Operations
The Setting 3 menu
Item
p
q
Description
Power on
Select the power on mode. Press and select the power on mode using
p
q
.
Manual—the projector must be powered on manually using the control panel or remote.
Auto—the projector powers on automatically when the main power switch is turned on.
No signal
power off
Sets the time to wait for the power to be turned off after the last operation is made with
no input signal. Press
and select the lamp interval using
p
q
.
Off/5 min./10 min./20 min./30 min.
Screen trigger
Enable or disable the screen trigger function. Press and select On or Off using
p
q
.
Fan mode
Select the desired fan mode. Press and select the fan mode using
p
q
.
Standard/High
Default input
select
Select the image source that the projector will search for automatically on startup. Press
and select the default input device using
p
q
.
Last source/Auto./Computer1/Computer2/Computer3/Y-PB-PR/Video/S-video
Video mode
Video: Press and select the default video mode using
p
q
.
Auto./NTSC/PAL/SECAM
S-video: Press
and select the default S-video mode using
p
q
.
Auto./NTSC/PAL/SECAM
Message
Enable or disable the onscreen warning and informational messages. Press and select On
or Off using
p
q
.
Filter warning
Set the interval between lter cleaning warning messages. Press and select the desired
interval using
p
q
.
Off/100H/200H/500H/1000H
Search mode
Set the search mode. Press and select the desired search mode using
p
q
.
Standard/Fine
Note
If [Power on] is set to [Auto] and there is a power outage, the projector will come on
once power is restored.
Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise
gets louder.) Set this option to use the projector, for example, at high altitude (over 1,200
meters above sea level).
Do not set Fan mode to [High] when using the projector at a lower altitude.”
Using the Setting menus (Continued)
The Status display screen provides a quick access to the detailed information on projector status.
The Status display menu contains four distinct tabs; Usage time, Input, Network, and Version.
Note
Information on the Status display screens is read only.
The Usage time screen
Item
p
q
Description
Lamp1 Displays the Lamp1 life remaining as a percentage.
Lamp2 Displays the Lamp2 life remaining as a percentage.
Lamp1 time Displays the Lamp1 total usage in hours.
Lamp2 time Displays the Lamp2 total usage in hours.
PJ time Displays the projector's total usage in hours.
Filter time Displays the lter total usage in hours.
Note
Displays [Lamp 1/2 time] as a measure of when the lamp should be replaced. (Cannot be
used as a counter of guaranteed lamp time.) When the displayed time approaches 2,000
hours, consult with a dealer about getting replacement for:
TLPLW25 for TDP-WX5400 (sold separately).
The Input screen
Item
p
q
Description
Input name Displays the input terminal that is currently being used.
Signal Displays the signal name of the currently being used.
H-sync. freq. Displays horizontal frequency in KHz
V-sync. freq. Displays vertical frequency in Hz
Video mode Displays video type, if present.
Sync Displays synchronization type.
Sync polarity Displays sychronization polarity.
Scan type Displays the scan type.
Using the Status display screen
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba TDP-WX5400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba TDP-WX5400 in the language / languages: English as an attachment in your email.

The manual is 7,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info