587680
23
Zoom out
Zoom in
Previous page
1/81
Next page
20
4
ELECTRIC WIRING
WARNING
Electrical work must be performed by a qualified electrician in accordance with the installation manual.
Ensure the air conditioner uses a designated power supply.
An insufficient power supply capacity or inappropriate installation may cause a fire.
When connecting the installation wiring, be sure that all fixing terminal are securely fixed.
Ensure earthling practice is correctly performed.
Grounding is necessary, if earthling practice is incomplete an electric shock maybe caused.
CAUTION
The installation fuse must be used for the power supply line of this outdoor unit.
Incorrect/incomplete wiring might cause an electrical fire or smoke.
Prepare the exclusive power supply for the outdoor unit.
Ensure an electrical leakage breaker is fitted. This is to prevent the risk of electric shock.
To Disconnect the Appliance from Main Power Supply.
This appliance must be connected to a main power supply by means of a switch with a contact separation of at
least 3 mm.
REQUIREMENT
Perform wiring of the power supply in conformance with the regulations of the local authorities.
For wiring of the power supply in the indoor unit, refer to the Installation Manual of the relevant indoor unit.
Never connect 220240V to the terminal block (U1, U2, U3, U4). (Fault will be caused.)
Arrange the electrical wiring so that they do not come into contact with high-temperature parts of the pipework;
this is to prevent the risk of insulation melting and causing a possible accident.
After connecting wires to the terminal block, secure wiring with cable clamp.
Install control wiring and refrigerant piping within the same line.
Do not turn on power of the indoor unit until vacuuming of the refrigerant pipe has finished.
For cabling of the power supply of the indoor units cabling between indoor and outdoor units, refer to the
Installation Manual of the indoor unit.
Knockout for
control wiring and
refrigerant piping
Knockout for
power supply wiring
Connection of power supply wire with control wire
Insert power supply wire and control wire after
removing knockout of the piping/wiring panel at front
side of the outdoor unit.
The knockout piping and the wiring hole are also
provided to the front surface, the right side, and the
rear side.
Note :
Be sure to separate the power supply wires and each control wire.
Arrange the power supply wires and each control wire so that they do not contact with the bottom surface of the
outdoor unit.
A terminal block (U3, U4 terminal blocks) for connecting an optional part Central remote controller etc. is
provided on the inverter unit, so be careful to miswiring.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba MCY-MAP0401HT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba MCY-MAP0401HT in the language / languages: English, German as an attachment in your email.

The manual is 2,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info