710116
20
Zoom out
Zoom in
Previous page
1/43
Next page
.
Malfunction Possible causes Remedy
25b.
Gate does not open/close fully
After closing, the gate opens again slightly.
Operator fails to move although the motor is
running.
Gate does not respond on impulse from the
hand transmitter - but does respond to push-
buttons or other impulse generators.
Gate does not respond to impulse from hand
transmitter nor to other impulse generators.
Insufficient range of hand transmitter.
.
Toothed belt or operator noisy.
Gate mechanics have altered.
Travel limit is incorrectly set
Gate blocks shortly before reaching the closed
position.
Travel limit is incorrectly set.
Operator is not engaged.
Battery in the hand transmitter is flat
Aerial not fitted.
No hand transmitter programmed.
See diagnostic display.
Battery in the hand transmitter is flat
Aerial not fitted.
On-site screening of the receiving signal.
Toothed belt dirty.
Tension of toothed belt too high.
Have the gate checked.
Reset travel limit .
Remove the obstruction.
Reset closed travel limit .
Re-engage the operator
Replace battery in the hand transmitter.
Plug in aerial.
Programme the hand transmitter ( menu
stage1).
See diagnostic display.
Replace battery in the hand transmitter.
Plug in aerial.
Connect external aerial (accessories).
Clean toothed belt.
Spray with silicone.
Detension the toothed belt.
17
17
21
Number State/Condition Diagnosis / Remedy.
0.
1
2
.
3
4
8
0
9
Operator starts up and "0" goes out
Gate neither opens nor closes.
Gate no longer closes.
Motor does not rotate.
Continuous impulse at the start input.
Operator is disengaged.
"0" stays displayed when door next opens and
closes, then goes out.
"0" continues to be displayed.
Safety test has been triggered.
Operator receives a start impulse at the START input or by a transmitter.
Normal operation.
At the STOP A connection no terminating resistance of 8.2Kohm.
External safety device has been activated.
STOP B connection is interrupted.
Photocell has been activated.
Call in a specialist.
Door no longer accepts a start impulse.
External impulse generator produces a permanent impulse signal (e.g. button
jammed).
Operator is disengaged, re-engage 24b.
Operator is in process of learning the force limit.
Caution: These operations are not force-monitored ! !
Briefly pull out mains plug. If "9" still displayed, change the control unit.
17
GB
Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!
Trouble-shooting
Important note: When working on the operator, always pull out the mains plug beforehand!!!
Diagnostic display
During operation, the display provides diagnostic information on any possible faults / malfunctions
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tormatic NovoGate at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tormatic NovoGate in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info