Manual Tormatic NovoGate (page 18 of 43) (English, German, Dutch, French, Spanish)

710116

Zoom out

Zoom in

1/43

Menu stage 5: opening force limit

Menu stage 6: closing force limit

15a

15b

If you previously quit the setting menu, press and

hold button for 3 seconds until "3" is displayed.

Then press button twice until "5" is displayed.

After approx. 2 seconds the display flashes showing

the set value of the force limit for the opening phase.

The factory setting is "6".

The force limit setting can be increased or decreased

via the and buttons. After selecting the setting,

press button . "6" is displayed.

After approx. 2 seconds the display flashes showing

the set value of the force limit for the closing phase.

The force limit setting can be increased or decreased

via the and buttons.

Finally, check the force settings and, if necessary,

repeat the setting procedure.

The force at the main closing edge must not exceed

the values specified in DIN EN 12453. Depending on

how the gate is used and the need to consider

national regulations, it may be necessary to

introduce protective measures over and above this.

If the force is set too high, this can result in

injury to persons or damage to property.

The factory setting is 4, if a higher setting is

selected, proof must be furnished that the

forces are being observed.

After setting the value, press button . “0” is

displayed.

- Position the force measuring device in the

closing area.

(If no measuring device is available, use, for

example, the operator's cardboard box).

- Start the gate from the open position.

- The gate travels towards the obstruction, stops

and reopens.

If alterations were made to the gate, then the force-

learning procedure must be repeated: Call up menu

stage 5 and keep the button pressed for 3

seconds. "0" is displayed. Then carry out force-

learning operations as explained under point

Briefly press button . "1" is displayed.

As soon as the display starts to flash, keep the button

of the hand transmitter, with which you would later

like to start the operator, pressed for approx. 1

second.

As soon as the code has been read in, the red

incremental display (a) flashes five times to

acknowledge it.

Further hand transmitters (up to a max. of 10 button

codes) can be programmed.

Press button . "2" is displayed.

Note: If no partial opening function is to be

programmed, press button once again .

"0" is displayed indicating that the programming is

completed. Press the second button on the hand

transmitter with which partial opening is to be

switched on .

As soon as the code has been read in, the red

incremental display (a) flashes five times to

acknowledge it.

After the code has been learned, briefly press button

. . "0" is displayed. End of menu.

Plug operator into mains whilst keeping button

pressed.

Checking the force limit device

10.

Menu stage 1: programming the starting

function for the hand transmitter

Menu stage 2: programming the partial

opening function for the hand transmitter

15b

Deleting all the hand transmitters programmed

for the operator:

Special Settings

Menu stage 7: light phases for the signal light

Automatic closing

Keep button pressed for 3 seconds. "3" is

displayed. Press button repeatedly until menu

stage 6 is displayed.

Keep button pressed for another 3 seconds until

"7" is displayed.

Menu Light Advance warning Flashing

value phase phase function

0 - - yes

1- --

2 60 s - yes

360s - -

4 - 3 s yes

5-3s-

6 60s 3s yes

7 60s 3s -

8 - 10 s yes

9-10s-

The setting can be altered via buttons and . The

factory setting is "0". Press button to end the

menu.

Cancellation of hold-open phase by

photocell

The functions are described in the operating

instructions.

Menu stage 8: Soft runs

Menu stage 9: Special functions

Normal operation

OPEN-CLOSE operation

operation with single-lane control

Automatic closing

Menu stage “A”: hold-open phases

Press button . "8" is displayed.

Menu Start Stop Start Stop

value Open Open Close Close

0 0000

1 15 0 15 0

2 0 15 0 60

3 15251560

4 15151560

5 15601560

6 15151515

7 15251585

8 15601585

9 only soft run

Press button . “9” is displayed.

Menu Operating mode

(standard setting ex factory)

1or

(only together with traffic light control)

External safety device

Photocell required

External safety device

Photocell required.

Set hold-open phase in menu stage A

Cancellation of the hold-open phase by the

impulse generator

Press button . “A " is displayed. These phases can

only be set for the menu values 2, 3 or 4 set under

menu stage “9”.

Menu Hold-open phase

value (plus 10s flashing as advance warning)

00s

110s

230s

360s

490s

5 120 s

6 150 s

7 180 s

8 210 s

9 240 s

Before initial operation, test the function and safety

of the operator.

All the requirements regarding the safe operation of

the system must be met.

In the case of systems accessed by the public or

used in the automatic closing mode, a photocell must

be installed.

It is recommended that a warning light be installed.

IIn the closing phase the force when distance

X is less than 500mm may not exceed 400N;

X is greater than 500mm may not exceed

1400N.

This is achieved by using safety profiles:

up to 400kg tormatic 35/ 50

up to 400kg tormatic 35/ 70

up to 400kg ASO GE 365

up to 400kg Gelbau 003.10

up to 400kg Mayser GP50

up to 200kg ASO GE 245

up to 200kg Bircher EPE36/45

up to 200kg Gelbau 016.10

Further insertable profiles can be obtained from the

manufacturer on request.

Because of the force limit device integrated into the

operator, the main closing edge may only be

equipped with a passive rubber profile (without

evaluation function).

The safety distances are adhered to if:

x is greater than 500mm or

y is less than100mm and X greater than 200mm

If the safety distances cannot be adhered to, then

this area can be safeguarded either by using a

protective fence or by applying a force limit.

In the case of a force limit, the rear closing edge must

be safeguarded by a safety profile as is the case with

the main closing edge.

Additionally, the distance of the STOP-OPEN soft

run must be correspondingly extended. (Menu 8

value 3 or 5).

If secondary closing edges form, these must be

equipped with safety profiles

up to 300kg tormatic 35 / 50

up to 400kg tormatic 35 / 70

Other profiles used a resistor for terminating voltage

of 8k2.

If access to the gate is safeguarded by fencing, the

maximum opening width A has to be adjusted to

distance X.

X l 120mm less than 18,5mm

X less than 300mm less than 29mm

X less than 500mm less than 44mm

X less than 850mm less than18,5mm.

Safe operation of the gate system

Main closing edge 16a

Gate weight Manufacturer Type

Rear closing edge 16b

Main closing edges 16c

gate weight manufacturer type

Protective fence 16d

Distance Opening size A

Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Tormatic NovoGate in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 1,18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Tormatic NovoGate Manual

Product: