483955
6
Zoom out
Zoom in
Previous page
1/52
Next page
6 Topcom Twintalker 5010
Topcom Twintalker 5010
13.2 Adjusting speaker volume
There are 15 levels of speaker volume
13.3 Receiving a signal
The unit is continuously in the receive mode when the unit is switched on and not
transmitting.
13.4 Transmitting a signal
13.5 Changing channels
13.6 CTCSS (Continuous Tone Coded Squelch System)
The 2 digit CTCSS code corresponds to a specific tone frequency the radio emits.
Two users, with the same channel and CTCSS set can hear one another. They will
not be able to hear anyone else on the channel unless the other radios have the same
exact CTCSS code enabled. The Twintalker 5010 has 38 CTCSS codes available.
13.7 Monitor
You can use the monitor feature to check for weaker signals in the current channel.
Press and hold the
MON\ -button to activate channel monitoring.
Release the
MON\ -button to stop monitoring.
13.8 Call tones
A call tone alerts other users that you want to start talking to.
13.8.1 Setting the call tone
The Twintalker 5010 has 10 call tones
13.8.2 Sending a call tone
Press the button briefly. The call tone will be transmitted on the set channel.
Press the volume up button in stand-by-mode
to increase the speaker volume. The volume level is
displayed.
Press the volume down button to decrease the
speaker volume.
Press and hold the PTT-button to transmit. The TX
LED will be on.
Hold the unit in a vertical position with the microphone
10 cm from the mouth and speak into the microphone.
Release the PTT-button when you want to stop
transmitting.
Press the -button or -button to change
the channel.
3
13
In order for other people to receive your transmission, they must
also be on the same channel and have set the same CTCSS code.
(See chapter 13.5 and 13.6)
12
12
To check the channel activity use the monitor function (see chapter
13.7). The maximum transmitting time is limited to 1 minute.
Release and press PTT-button
to restart transmitting.
12
10
Press the -button , the current CTCSS code
flashes on the display.
Press the -button
or -button to
change to another code.
Press the PTT-button
to confirm and return to
stand-by mode.
Press the -button two times.
Press the -button or -button to change
to another call tone. Select ‘0’ to disable the call tones.
Press the PTT-button to confirm and return to
stand-by mode.
9
5
10
12
It is recommended to set a CTCSS code for each channel.
This way you will have minimum interference from other
users on the same channel.
To disable CTCSS code, set the code to ‘0’.
If no button is pressed within 5 seconds during setting, the unit
will return to standby.
4
4
9
5
10
12
11
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Topcom Twintalker 5010 - RC 6402 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Topcom Twintalker 5010 - RC 6402 in the language / languages: English, German, Dutch, French, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 0,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info