484000
8
Zoom out
Zoom in
Previous page
1/121
Next page
Babytalker 1020
6
®
5.4.2 Connecting the baby unit to the mains
- Plug the small connector of the power adapter into the
power adapter jack on the side of the baby unit. A click
indicates, the jack is locked into position.
- Connect the power adapter (7,5V DC / 300mA) to a mains
socket (230-240V~ 50Hz).
5.4.3 Inserting batteries into the parents' unit
- Remove the belt clip.
- Push the battery cover and slide it downwards.
- Install the rechargeable battery pack following the polarity as
illustrated.
- Re-install the battery cover and belt clip.
5.4.4 Charging batteries in the parents' unit
- Connect the power adapter (7,5V DC / 300mA) to a
main socket (230-240V~ 50Hz).
- The flashing battery charge indicator in the display
shows that the batteries are being charged:
6 Operating the device
6.1 Switching the parents' unit and baby unit on and off
- Press the on/off button to switch on the parents' unit. The display illuminates.
- To switch on the baby unit, press the on/off button . The display illuminates.
- To switch off the parents' unit, press and hold the on/off button until the display goes out
- To switch off the baby unit, press and hold the on/off button until the display goes out.
6.2 Setting the channel
To have communication between the baby unit and the parents’ unit they need to be set both on the same channel.
- Press the channel up or channel down button on the parent to select the channel of the parent
unit.
- Press the channel up or channel down button on the baby unit to select the same channel of
the parent unit.
Once both units have the same channel, the parents’ unit can receive the signal from the baby unit.
When on one or both units is displayed, the privacy mode is activated. Check chapter “Activating privacy mode”
on page 7
.
Only use the enclosed power adapter.
WARNING
Injury and material damage can be caused by using
non-rechargeable batteries in the parents' unit!
Only use the Ni-MH battery pack supplied with the
product.
The parent unit can only be used with the
enclosed a Ni-MH battery pack. It cannot
be used with single cell Ni-MH batteries!
The batteries take about 12 hours
to charge.
The batteries are charged continuously.
Therefore the flashing battery charge
indicator in the display is still visible even
when the batteries are fully charged.
22
MADE IN CHINA
MUST BE RECYCLED OR DISPOSED OF PROPERLY
Ni-MH
13
13
9
18
14
9
18
3
4
15
16
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Topcom Babytalker 1020 - KS-4212 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Topcom Babytalker 1020 - KS-4212 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 38,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Topcom Babytalker 1020 - KS-4212

Topcom Babytalker 1020 - KS-4212 User Manual - Dutch - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info