Manual Toolson KGZ2550PRO (page 25 of 296) (All languages)

782362

Zoom out

Zoom in

1/296

25GB

• Before you press the ON/OFF switch check that the

saw blade is tted correctly. Moving parts must run

smoothly.

• Before you connect the equipment to the power sup-

ply make sure the data on the rating plate are dentical

to the mains data.

8. Attachment and operation

8.1 Attaching the saw (Fig. 1-6)

• To adjust the rotary table (16), push the locking lever

(13) downwards and pull the lower indexed position

lever (12) upwards with your index nger.

• Rotate the rotary table (16) and pointer (14) to the

desired angle on the scale (15) and lock in place by

folding up the locking lever (13).

• Pressing the machine head (5) lightly downwards and

removing the locking bolt (24) from the motor bracket

at the same time disengages the saw from the low-

est position.

• Swing the machine head (5) up until the release lever

(3) latches into place.

• It is possible to secure the clamping device (8) to the

left or right on the stationary saw bench (17).

• Attach the workpiece supports (9) to the xed saw

table (17) as shown in Figure 6a,b,c and push all the

way through. Secure the shafts with the retaining

springs to prevent them from slipping out accidentally.

The fasten in the desired position with the screw (10).

• It is possible to tilt the machine head (5) a max. 45° to

the left by loosening the set screw (22).

8.2 Precision adjustment of the stop for crosscut

90° (Fig. 3,5,18)

• No stop angle included.

• Lower the machine head (5) and secure using the

locking bolt (24).

• Loosen the set screw (22).

• Position the angle stop (a) between the saw blade (7)

and the rotary table (16).

• Slacken the counternut (d). Adjust the adjusting screw

(30) until the angle between the saw blade (7) and ro-

tary table (16) is 90°.

• Retighten the counternut (d) to secure this setting.

• Subsequently check the position of the angle indica-

tor. If necessary loosen the pointer (20) using a Philips

screwdriver, set to position 0° on the angle scale (19)

and re-tighten the retaining screw.

8.3 Precision adjustment of the stop for mitre cut 45°

(Fig. 1,3,5,19)

• No stop angle included.

• Lower the machine head (5) and secure using the

locking bolt (24).

• Fix the rotary table (16) in the 0° position.

• Loosen the set screw (22) and use the handle (1) to

angle the machine head (5) 45° to the left.

• 45° - position angle stop (b) between the saw blade

(7) and rotary table (16).

• Slacken the counternut (c). Adjust the adjusting screw

(31) until the angle between the saw blade (7) and ro-

tary table (16) is precisely 45°.

• Retighten the counternut (d) to secure this setting.

8.4 Cross cut 90° and turntable 0° (Fig.1,2,6,7)

In the case of cutting widths up to approx. 100 mm it is

possible to x the traction function of the saw with the

set screw (23) in the rear position. In this position the

machine can be operated in cross cutting mode. If the

cutting width is over 100 mm then it is necessary to en-

sure that the set screw (23) is loose and the machine

head (5) can move.

Attention! For 90° mitre cuts, the moveable stop rail (28)

must be xed in the inner position.

• Open the set screw (29) on the moveable stop rail (28)

and push the moveable stop rail (28) inwards.

• The moveable stop rail (28) must be locked in a po-

sition far enough from the inner position that the dis-

tance between the stop rail (28) and the saw blade (7)

is no more than 5 mm.

• Before making the cut, check that no collision could

occur between the stop rail (28) and the saw blade (7).

• Tighten the set screw (29) again. (2x 8.3 +8.4)

• Move the machine head (5) to its upper position.

• Use the handle (1) to push back the machine head

(5) and x it in this position if required (dependent on

the cutting width).

• Place the piece of wood to be cut at the stop rail (18)

and on the turntable (16).

• Lock the material with the clamping device (8) on the

xed saw table (16) to prevent the material from mov-

ing during the cutting operation.

• Push down the release lever (3) to release the ma-

chine head (5).

• Press the ON/OFF switch (2) to start the motor.

• With the drag guide (23) xed in place:

use the handle (1) to move the machine head (5) steadily

and with light pressure downwards until the saw blade (7)

has completely cut through the work piece.

• With the drag guide (23) not xed in place:

pull the machine head (5) all the way to the front.

Lower the handle (1) to the very bottom by applying

steady and light downward pressure. Now push the

machine head (5) slowly and steadily to the very back

until the saw blade (7) has completely cut through the

work piece.

• When the cutting operation is completed, move

the machine head (5) back to its upper (home)

position and release the ON/OFF button (2).

Attention! The machine executes an upward stroke

automatically due to the return spring, i.e. do not re-

lease the handle (1) after completing the cut; instead

allow the machine head to move upwards slowly whilst

applying light counter pressure.

8.5 Cross cut 90° and turntable 0° - 45° (Fig. 1,6,7)

The crosscut saw can be used to make crosscuts of 0°

-45° to the left and 0° -45° to the right in relation to the

stop rail.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Toolson KGZ2550PRO in the language / languages: All languages as an attachment in your email.

The manual is 13.89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Toolson KGZ2550PRO Manual

Product: