658790
16
Zoom out
Zoom in
Previous page
1/29
Next page
12
LNB Type Shows which type of LNB is supported universal LNB.
LNB Freq. Show the Local Oscillator Frequency of the Universal LNB 9750/10600.
22KHz Tone This setting shows that it is set to automatically. Auto.
DiSEqC 1.0 Select a port 1 to 4 according to the connected satellite dish.
DiSEqC 1.1 Select a port 1 to 16 according to the connected satellite dish.
Transponder Press OK to open the list of available transponders for the chosen satellite, in order
to check your reception or align the antenna.
Press the RED button to start scanning on the selected transponder if selection is on Transponder.
Press the RED button to start scanning on the whole satellite if selection is on Satellite.
7.1.3 Motor Settings
If you use DiSEqC 1.2 or GOTO-X, you can install satellites which are received by a motorized
dish. For setup and installation as well as for correct setup of the positions in the receiver we highly
recommend taking the advice of a professional and experienced dish installer. The menu allows you to
congure the motor type and to adjust the motor position for the satellite which you want to receive.
Satellite Press OK to open the list of available satellites and choose a satellite with pq or
P+/P- and conrm by pressing OK.
Transponder Press OK to open the list of available transponders if you need to adjust a
transponder for the above selected satellite.
DiSEqC Motor Select between type DiSEqC 1.2 and GOTO-X or O.
Selection on DiSEqC 1.2
Move: Press t u to move the dish to East or West. Carefully move until you can observe
that both signal bars show acceptable reception levels. When you have found the
selected satellite press
and select Yes to save the position.
Move ne: Here you can move the motor in small steps to adjust it more precisely.
Limit: Press OK to open this submenu in order to adjust mechanical limits for your
dish. This is only necessary if your dish could interfere with a wall, tree, or similar
mechanical margins.
Go To: Position Press OK to move the motor to the centre position of0 degrees. This is only needed
for the rst time to adjust the dish correctly or select a number from a position.
Save/Recalculation
To store and save a position or do a recalculation.
Selection on GOTO-X
Congure the motor position through the GOTO-X function. Enter your geographical position. The
motor is able to nd all available satellite positions itself.
Antenna Position:
Press OK to open submenu.
Use the 0 ~ 9 buttons to enter the value of your longitude.
Select East or West.
Use the 0 ~ 9 buttons to enter the value of your latitude.
Select North or South. At the end select Save and press
OK to conrm the values.
GOTO: Press OK to move the motor to the wanted position
NOTE: Detailed information about correct geographical values for your location
can be found on websites like dishpointer.com, itouchmap.com or other
reliable sources.
7.1.4 Channel Search
Use this menu to perform an automatic, network or transponder channel search or to search on all
satellites that have been setup. Use pq to highlight an item and t u to change settings. Below are
the settings listed you can nd in the search method selection.
Satellite Select the satellite on which you would like to search for channels.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson THS815 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson THS815 in the language / languages: English as an attachment in your email.

The manual is 1,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info