Manual Thomson THS814 (page 16 of 30) (English)

658789

Zoom out

Zoom in

1/30

7.1.2 Motor Setting

If you are using DiSEqC 1.2 or USALS, you can install satellites which are received by a motorised

dish. For the correct installation and positioning of your motor, we recommend the support/advice

of a professional and experienced installer. Here you can congure the motor type and set the motor

position for a satellite that you want to receive.

Satellite Press OK to open the list of available satellites and select one by using the pq or

P+/P- buttons, then press OK again for conrmation.

Transponder Press OK to open the list of available transponders if you like to set a specic

transponder for the selected satellite.

DiSEqC Motor Choose between DiSEqC 1.2 and USALS or O. Per default it is Off because of pre-

dened setup for DiSEqC 1.0.

DiSEqC 1.2 selection

Move step-wise Press t u to move your antenna east or west. Move carefully until you see that

both signal beams have an acceptable reception level. When you nd the selected

satellite, press

and select Yes to save the position.

Move continuously

Use this function to move quickly to a desired position by holding down the t or u

key, depending on the direction in which you want to move the antenna. Also, be

very careful with it, so you do not bump into obstacles.

Limit Press OK to open this sub-menu, which allows you to set the mechanical limits for

your motor. This is only necessary if your antenna is mounted which means, that a

wall, a tree or similar physical blockages could interfere with a free movement of the

antenna or motor.

Save to this position

You can store this position between 0 and 63, OK can be used again as described

above.

Save/Recalculation

With Save and Recalculate, you can set whether the position should be saved or a

new calculation should be made after setting this position.

Go to position Press OK to move the motor to the centre position. This is only necessary for the rst

time to set the antenna correctly. Then you can also select a number of a position

you already have stored or check the antenna position.

USALS selection

Congure the motor position by using the USALS function. Enter your geographic location. The motor

is able to calculate all available satellite positions, preconditioned this function is also supported by

the motor. Use pq to select the Antenna Position sub-menu.

Antenna position:

Press OK to open the submenu. Use the 0 ~ 9 buttons to enter the degree of

longitude. Next, select East or West, then 0 ~ 9 to enter the latitude. Finally, specify

North or South. Finally, select Save and press OK to conrm your entries.

Go to position Press OK to move the motor to the desired satellite position. After computation, you

can also select other satellites, go to Satellite and select the desired one from the

list.

NOTE: For detailed information about correct geographic locations for your

location, visit websites such as dishpointer.com, itouchmap.com, or other

reliable sources such as professional journals.

7.1.3 Channel Search

In this menu, you can perform an automatic, network or transponder search. You can also search for

channels on all installed satellites. Use the pq buttons to highlight the desired item and use t u to

change the settings.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Thomson THS814 in the language / languages: English as an attachment in your email.

The manual is 1,06 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Thomson THS814

Thomson THS814 User Manual - German - 32 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Thomson THS814 Manual

Product: