600937

Thermona THERM EL 15 Manual

21
Zoom out
Zoom in
Previous page
1/37
Next page
21
connected.
In the case of a defective sensor or if it is not connected, the boiler is controlled in the tEr (like at P3.1 = 1) mode.
otP 4 Heating is controlled by external regulator which is connected by way of the OpenTherm Plus
interface.
In the case of defective communication or regulator, the boiler is controlled in the tEr (like at P3.1 = 1) mode.
ot- 5 Heating is controlled by external regulator which is connected by way of the OpenTherm Lite
interface.
In the case of defective communication or regulator, the boiler is controlled in the tEr (like at P3.1 = 1) mode.
diS P3.2 Menu display type (mnemotechnical texts/numerical parameters)
Settings options:
diS = 012, AbC (P3.2 = 0, 1
), leading value
AbC (1).
9. Putting the boiler into operation
Service engineer with authorization from the manufacturer is obliged to make a verifiable
demonstration for the user of the boiler operation, its individual parts, safety components and control
methods prior to putting the boiler into operation and fill in the letter of guarantee and hand over this
Operation and Maintenance Manual to the user.
User is bound to observe the correct use of the boiler in accordance with this Manual; this is a basic
precondition for acknowledgement of the warranty. It is further strictly forbidden to interfere with any of the
sealed parts inside the boiler!
Warning:
The settings of the boiler output range and other parameters must be in compliance with the technical data.
Any excess loads or incorrect use of the boiler can cause damage to its components. Warranty does not apply to
the components which suffer this kind of damage!
♦ General instructions:
The following must be checked before the electric boiler is set into operation:
connection to the heating system
opening of the fittings separating the electric boiler from the system and securing them against
manipulation
charging (may be followed by pressurizing) the system by soft water and subsequent bleeding
electric connection and protection in line with the CSN standards. For further details refer to the
Chapter “Wall-mounting of the boiler”.
The procedure for setting the boiler into operation is as follows:
switch on the main circuit breaker (switch) in the power intake, switch on the boiler by pressing the O/I
button for heating actuation
set the desired outlet boiler temperature to maximum
check the correct functioning of all safety thermostats and control components
check the settings of the boiler output range, potentially adjust the settings on the basis of the heated
building.
… 21 …


Need help? Post your question in this forum.

Forumrules
1

Forum

thermona-therm-el-15

Reset search

  • I Have an EL15 and cannot see how to connect a 3 way motorised valve. Manual shows position on diagram but how is connection physically made? Please help Submitted on 28-9-2022 at 18:47

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thermona THERM EL 15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thermona THERM EL 15 in the language / languages: English as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info