636645
12
Zoom out
Zoom in
Previous page
1/23
Next page
6
Maintenance and storage
The engine shall be stopped when carrying out
maintenance and cleaning operations, when
changing tools and when being transported by
means other than under its own power.
Check regularly that all bolts and nuts are
tightened. Retighten if necessary.
The engine must be completely cooled before
storing indoors or covered.
If the machine unused for a period of time,
please refer to the instructions in this manual.
Maintain or replace safety and instruction
labels, as necessary.
Only use orginal spare parts or accessories. If
not orginal parts or accessories is used, the
liablility is no longer applied.
Miscellaneous
The motor is not pre-filled with oil.
Always before start check the engine oil level.
Factory-fitted control devices, such as the
handle-mounted clutch cable, must not be
removed or exposed.
Only drain the fuel tank outdoors. Gasoline is
extremely flammable and the fumes are
explosive.
Ensure that the machine is properly secured
when transported on a flatbed etc.
Waste electrical products must not be
disposed of with the household waste. This
tool should be taken to your local recycling
centre for safe treatment.
The lawn rider is manufactured according to the latest
safety requirements. These include a blade brake that
stops the motor and blade in 3 seconds when the blade
brake. Every precaution is only effective when it is
followed exactly. Use the following description when
you mount your lawnmower.
Identification of the parts
See Illustration 1
Notice: the illustrations may vary from your present
model
A. Choke.
B. Gear.
C. Ignition key - Electric starter.
D. Water nozzle.
E. Height adjustment.(cutting deck)
F. Brake/clutch pedal
G. Parking brake.
H. Coupling rod. (cutting deck)
I. Safety switch.
J. Grass collector (only model 6100E)
Mounting
Unpacking: Illustration M1
Remove the mower from the box by pulling the machine
out form the side. The box contains:
1 pcs. Mower
1 pcs. Steering wheel.
1 pcs Coupling rod
1 pcs Grass collector (only model 6100E)
Assembly instructions (illustration 2+5)
1. Mount the coupling rod for the cutting deck as
shown.
2. Mount the steering wheel to steer axle, fasten
as shown.
3. Mount the grasscollector and attach to mower
as shown.
4. Open the seat flap, fit and install the seat as
shown.
5. It is recommended to mount the safety bolt
and pin as shown in illustration 5. This fix the
cover to the chassis of the machine.
Technical installation
6. Add oil on the engine (cf. engine manual)
7. Cennect the wire to the battery (illustration 2.6)
8. Ensure that the safety switch under seat and
on rear plate (only model 6100E) is activated.
Tyre pressure
Check tyre pressure before start.
The correct tyre pressure is 1.8 bar on front wheels and
1.3 bar on rear wheels
Important: When tyre pressure is too low the valves
and the inner tube may be damaged.
Battery
Charge the battery before use
Before the electric start function is used, the battery
must be charged for min 5 hours. Put the charger plug
into the hole in the battery (open the yellow cover first)
and connect the charger to a power supply. See
illustration 4.
Charging during the season
The battery is charged a little during use, buy it will
likely be necessary to charge the battery a couple of
times during the season - depending if the number of
start/stops of the engine. Put it for charging for around 5
hours.
Storage of battery
The battery must always be stored dry and warm during
the winter. Never expose it for low temperatures.
Charge the battery completely before storing and then
place the lawn mower in a place where it is not exposed
to frost. Alternatively cover the battery with a thick
carpet or similar, If the mower is in a shed/garage
where there may be cold.
Charge the battery 1-2 times during the winter (at least
every 3
rd
month) to make sure the battery keeps it full
capacity.
Incorrect storage can damage the battery, and is not
covered by warranty.
12


Need help? Post your question in this forum.

Forumrules
1

Forum

texas-rider-6100e

Reset search

  • My Texas rider 6100e will not start. The motor spins on operation but will not fire up Submitted on 22-3-2018 at 15:48

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Texas Rider 6100E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Texas Rider 6100E in the language / languages: English, German, Danish as an attachment in your email.

The manual is 1,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info